Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001E6J0
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 10/2019]
Title: UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): PARK / NEUTRAL POSITION SWITCH: REMOVAL; 2019 MY RAV4 [11/2018 - 10/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during park/neutral position switch assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane control system

2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for Gasoline model)*

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system (for Gasoline model)

2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Reset back door close position

Power back door system (for Gasoline model)

2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

ECM

Perform Vehicle Identification Number (VIN) or frame number registration

DTC P063051 is output

w/ Canister Pump Module: 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): REGISTRATION

w/o Canister Pump Module: 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): REGISTRATION

Code registration

Engine start function

w/ Smart Key System: 2019 MY RAV4 [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

w/o Smart Key System: 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (for Gasoline Model without Smart Key System): REGISTRATION

  • If transaxle compensation code read from ECM
    • Perform reset memory
    • Transfer transaxle compensation code
    • Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

for Initialization: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

for Registration: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION

  • If transaxle compensation code not read from ECM
    • Perform reset memory
    • Transfer transaxle compensation code
    • Perform road test to allow ECM to learn

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

System Name

See Procedure

Vehicle enrolled in Toyota Entune system or safety connect system

6 minutes

Vehicle not enrolled in Toyota Entune system and safety connect system

1 minute

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

  • Make sure to apply the parking brake and chock a wheel before performing this procedure.
  • If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. REMOVE BATTERY

Click here 2019 MY RAV4 [11/2018 - 10/2019]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL

3. REMOVE ECM

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL

4. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here 2019 MY RAV4 [11/2018 - 10/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

(a) While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.

*a

Clip

*b

45° to 60°

6. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

(a) Disconnect the park/neutral position switch assembly connector.

(b) Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.

(c) Remove the 2 bolts and park/neutral position switch assembly from the automatic transaxle case sub-assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.