Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001E7IE |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 - 10/2022] |
Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: B15FE,B15FF; XM Tuner Antenna Disconnected; 2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022] |
DTC
|
B15FE
|
XM Tuner Antenna Disconnected
|
DTC
|
B15FF
|
XM Tuner Antenna Short
|
DESCRIPTION
These DTCs are stored when a malfunction occurs in the No. 1 amplifier antenna assembly which is connected to the radio and display receiver assembly.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B15FE
|
XM Tuner Antenna Disconnected
|
The No. 1 amplifier antenna assembly is not connected
|
-
Antenna cord sub-assembly
-
No. 3 antenna cord sub-assembly
-
No. 4 antenna cord sub-assembly
-
No. 1 amplifier antenna assembly
-
Radio and display receiver assembly
|
B15FF
|
XM Tuner Antenna Short
|
A short occurs in the No. 1 amplifier antenna assembly
|
-
Antenna cord sub-assembly
-
No. 3 antenna cord sub-assembly
-
No. 4 antenna cord sub-assembly
-
No. 1 amplifier antenna assembly
-
Radio and display receiver assembly
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
-
A communication malfunction DTC may be stored.
-
The radio and display receiver assembly may not operate normally.
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
PROCEDURE
1.
|
CHECK CONNECTION OF ANTENNA CABLE
|
(a) Check if the No. 1 amplifier antenna assembly cable is securely connected to the radio and display receiver assembly.
OK:
No. 1 amplifier antenna assembly cable is securely connected.
NG |
|
SECURELY CONNECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY CABLE
|
OK
|
|
|
(a) Clear the DTCs.
Click here
Body Electrical > Navigation System > Clear DTCs
(b) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
NG
|
|
|
3.
|
CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the No. 1 amplifier antenna assembly.
|
|
*a
|
Front view of wire harness connector
(No. 1 Amplifier Antenna Assembly)
|
*b
|
Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
|
|
|
(b) Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-3 - B-5
|
Always
|
Below 1 Ω
|
A-3a - B-5a
|
Always
|
Below 1 Ω
|
A-3 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
4.
|
CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
|
|
*a
|
Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
|
*b
|
Front view of wire harness connector
(to Antenna Cord Sub-assembly)
|
|
|
(b) Disconnect the antenna connector from the antenna cord sub-assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
B-5 - C-5
|
Always
|
Below 1 Ω
|
B-5a - C-5a
|
Always
|
Below 1 Ω
|
B-5 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
5.
|
CHECK ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
|
|
*a
|
Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
|
*b
|
Front view of wire harness connector
(to Radio and Display Receiver Assembly)
|
|
|
(b) Disconnect the antenna connector from the radio and display receiver assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C-5 - D-1 (SXM)
|
Always
|
Below 1 Ω
|
C-5a - D-1a
|
Always
|
Below 1 Ω
|
C-5 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
6.
|
CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
|
(a) Replace the No. 1 amplifier antenna assembly with a new or known good one.
Click here
(b) Clear the DTCs.
Click here
Body Electrical > Navigation System > Clear DTCs
(c) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
OK |
|
END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)
|
|