| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001E7JB |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 10/2019] |
| Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: Speaker Circuit; 2019 MY RAV4 RAV4 HV [11/2018 - 10/2019] | ||
|
Speaker Circuit |
DESCRIPTION
for 6 Speakers
-
If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, DCM (telematics transceiver)* or speakers.
- *: w/ Manual (SOS) Switch
for 9 Speakers
-
If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver) or speakers.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
- When replacing the DCM (telematics transceiver), make sure to replace it with a new one (w/ Manual [SOS] Switch).
-
Before replacing the DCM (telematics transceiver), refer to Registration (w/ Manual [SOS] Switch).
for Gasoline Model: Click here
![2019 MY RAV4 [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION](/t3Portal/stylegraphics/info.gif)
for HV Model: Click here
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
PROCEDURE
|
1. |
CHECK MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for 6 Speakers |
A |
|
for 9 Speakers |
B |
| B |
|
|
|
2. |
CHECK SPEAKER (OPERATION CHECK) |
|
(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check. Click here
|
|
(b) Perform the operation check above and determine the speaker that is not operating.
|
Not Operating Speaker |
Proceed to |
|---|---|
|
Front No. 1 speaker assembly or front No. 2 speaker assembly |
A |
|
Rear speaker assembly |
B |
HINT:
If sound cannot be heard from any speaker, inspect all of them.
| B |
|
|
|
3. |
CHECK MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
w/ Manual (SOS) Switch |
A |
|
w/o Manual (SOS) Switch |
B |
| B |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER)) |
(a) Disconnect the G4 radio and display receiver assembly connector.
(b) Disconnect the I1 and J1 front No. 1 speaker assembly connectors.
(c) Disconnect the G5 and G6 front No. 2 speaker assembly connectors.
(d) Disconnect the G9 DCM (telematics transceiver) connector.
(e) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G4-1 (FR+) - G9-2 (SPI+) |
Always |
Below 1 Ω |
|
G4-6 (FR-) - G9-3 (SPI-) |
Always |
Below 1 Ω |
|
G9-5 (SPO+) - G5-4 (TWR+) |
Always |
Below 1 Ω |
|
G9-6 (SPO-) - G5-2 (TWR-) |
Always |
Below 1 Ω |
|
G4-2 (FL+) - G6-4 (TWL+) |
Always |
Below 1 Ω |
|
G4-7 (FL-) - G6-2 (TWL-) |
Always |
Below 1 Ω |
|
I1-2 (+) - G5-3 (+) |
Always |
Below 1 Ω |
|
I1-1 (-) - G5-1 (-) |
Always |
Below 1 Ω |
|
J1-2 (+) - G6-3 (+) |
Always |
Below 1 Ω |
|
J1-1 (-) - G6-1 (-) |
Always |
Below 1 Ω |
|
G4-1 (FR+) or G9-2 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
G4-6 (FR-) or G9-3 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
G9-5 (SPO+) or G5-4 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
G9-6 (SPO-) or G5-2 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
G4-2 (FL+) or G6-4 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
G4-7 (FL-) or G6-2 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
I1-2 (+) or G5-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
I1-1 (-) or G5-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
J1-2 (+) or G6-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
J1-1 (-) or G6-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
6. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
|
(a) Remove the DCM (telematics transceiver). Click here
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (SPI+) - 5 (SPO+) |
Always |
Below 1 Ω |
|
3 (SPI-) - 6 (SPO-) |
Always |
Below 1 Ω |
|
2 (SPI+) - 3 (SPI-) |
Always |
10 kΩ or higher |
|
5 (SPO+) - 6 (SPO-) |
Always |
10 kΩ or higher |
|
2 (SPI+) or 5 (SPO+) - Body ground |
Always |
10 kΩ or higher |
|
3 (SPI-) or 6 (SPO-) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
|
7. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the G4 radio and display receiver assembly connector.
(b) Disconnect the I1 and J1 front No. 1 speaker assembly connectors.
(c) Disconnect the G5 and G6 front No. 2 speaker assembly connectors.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G4-1 (FR+) - G5-4 (TWR+) |
Always |
Below 1 Ω |
|
G4-6 (FR-) - G5-2 (TWR-) |
Always |
Below 1 Ω |
|
G4-2 (FL+) - G6-4 (TWL+) |
Always |
Below 1 Ω |
|
G4-7 (FL-) - G6-2 (TWL-) |
Always |
Below 1 Ω |
|
I1-2 (+) - G5-3 (+) |
Always |
Below 1 Ω |
|
I1-1 (-) - G5-1 (-) |
Always |
Below 1 Ω |
|
J1-2 (+) - G6-3 (+) |
Always |
Below 1 Ω |
|
J1-1 (-) - G6-1 (-) |
Always |
Below 1 Ω |
|
G4-1 (FR+) - Body ground |
Always |
10 kΩ or higher |
|
G4-6 (FR-) - Body ground |
Always |
10 kΩ or higher |
|
G4-2 (FL+) - Body ground |
Always |
10 kΩ or higher |
|
G4-7 (FL-) - Body ground |
Always |
10 kΩ or higher |
|
G5-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
G5-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
G6-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
G6-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
8. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
9. |
CHECK FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Replace the front No. 2 speaker assembly with a new or known good one.
Click here
(b) Check the malfunction disappears.
OK:
Malfunction disappears.
HINT:
- Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
- When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
- Perform the above inspection on both the LH and RH sides.
| OK |
|
END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) |
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
|
10. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
(a) Disconnect the G4 radio and display receiver assembly connector.
(b) Disconnect the K1 and L1 rear speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G4-4 (RR+) - K1-2 (+) |
Always |
Below 1 Ω |
|
G4-9 (RR-) - K1-1 (-) |
Always |
Below 1 Ω |
|
G4-3 (RL+) - L1-2 (+) |
Always |
Below 1 Ω |
|
G4-8 (RL-) - L1-1 (-) |
Always |
Below 1 Ω |
|
G4-4 (RR+) - Body ground |
Always |
10 kΩ or higher |
|
G4-9 (RR-) - Body ground |
Always |
10 kΩ or higher |
|
G4-3 (RL+) - Body ground |
Always |
10 kΩ or higher |
|
G4-8 (RL-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
11. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
12. |
CHECK SPEAKER (OPERATION CHECK) |
|
(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check. Click here
|
|
(b) Perform the operation check above and determine the speaker that is not operating.
|
Not Operating Speaker |
Proceed to |
|---|---|
|
Front No. 1 speaker assembly or front No. 3 speaker assembly |
A |
|
Front No. 2 speaker assembly |
B |
|
Rear speaker assembly |
C |
|
Rear No. 2 speaker assembly |
D |
HINT:
If sound cannot be heard from any speaker, inspect all of them.
| B |
|
| C |
|
| D |
|
|
|
13. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
(a) Disconnect the M2 stereo component amplifier assembly connector.
(b) Disconnect the J1 and I1 front No. 1 speaker assembly connectors.
(c) Disconnect the G6 and G5 front No. 3 speaker assembly connectors.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M2-9 (FR+) - G5-4 (TWR+) |
Always |
Below 1 Ω |
|
M2-24 (FR-) - G5-2 (TWR-) |
Always |
Below 1 Ω |
|
M2-14 (FL+) - G6-4 (TWL+) |
Always |
Below 1 Ω |
|
M2-29 (FL-) - G6-2 (TWL-) |
Always |
Below 1 Ω |
|
J1-2 (+) - G6-3 (+) |
Always |
Below 1 Ω |
|
J1-1 (-) - G6-1 (-) |
Always |
Below 1 Ω |
|
I1-2 (+) - G5-3 (+) |
Always |
Below 1 Ω |
|
I1-1 (-) - G5-1 (-) |
Always |
Below 1 Ω |
|
M2-9 (FR+) - Body ground |
Always |
10 kΩ or higher |
|
M2-24 (FR-) - Body ground |
Always |
10 kΩ or higher |
|
M2-14 (FL+) - Body ground |
Always |
10 kΩ or higher |
|
M2-29 (FL-) - Body ground |
Always |
10 kΩ or higher |
|
G6-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
G6-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
G5-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
G5-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
14. |
INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
(a) Remove the front No. 3 speaker assembly.
Click here
(b) Inspect the front No. 3 speaker assembly.
Click here
| NG |
|
|
|
15. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
16. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the M2 stereo component amplifier assembly connector.
(b) Disconnect the G7 and G8 front No. 2 speaker assembly connectors.
(c) Disconnect the G9 DCM (telematics transceiver) connector.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M2-10 (TWL+) - G8-1 (+) |
Always |
Below 1 Ω |
|
M2-25 (TWL-) - G8-2 (-) |
Always |
Below 1 Ω |
|
M2-13 (TWR+) - G9-2 (SPI+) |
Always |
Below 1 Ω |
|
M2-28 (TWR-) - G9-3 (SPI-) |
Always |
Below 1 Ω |
|
G9-5 (SPO+) - G7-1 (+) |
Always |
Below 1 Ω |
|
G9-6 (SPO-) - G7-2 (-) |
Always |
Below 1 Ω |
|
M2-10 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
M2-25 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
M2-13 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
M2-28 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
G9-5 (SPO+) - Body ground |
Always |
10 kΩ or higher |
|
G9-6 (SPO-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
17. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG |
|
|
|
18. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
19. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
(a) Disconnect the M2 stereo component amplifier assembly connector.
(b) Disconnect the L1 and K1 rear speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M2-12 (RR+) - K1-2 (+) |
Always |
Below 1 Ω |
|
M2-27 (RR-) - K1-1 (-) |
Always |
Below 1 Ω |
|
M2-11 (RL+) - L1-2 (+) |
Always |
Below 1 Ω |
|
M2-26 (RL-) - L1-1 (-) |
Always |
Below 1 Ω |
|
M2-12 (RR+) - Body ground |
Always |
10 kΩ or higher |
|
M2-27 (RR-) - Body ground |
Always |
10 kΩ or higher |
|
M2-11 (RL+) - Body ground |
Always |
10 kΩ or higher |
|
M2-26 (RL-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
20. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
21. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the M2 stereo component amplifier assembly connector.
(b) Disconnect the N1 rear No. 2 speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M2-15 (WFR+) - N1-4 (WF+) |
Always |
Below 1 Ω |
|
M2-30 (WFR-) - N1-1 (WF-) |
Always |
Below 1 Ω |
|
M2-8 (WFL+) - N1-2 (WF+) |
Always |
Below 1 Ω |
|
M2-23 (WFL-) - N1-3 (WF-) |
Always |
Below 1 Ω |
|
M2-30 (WFR+) - Body ground |
Always |
10 kΩ or higher |
|
M2-23 (WFR-) - Body ground |
Always |
10 kΩ or higher |
|
M2-8 (WFL+) - Body ground |
Always |
10 kΩ or higher |
|
M2-23 (WFL-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
22. |
REPLACE REAR NO. 2 SPEAKER ASSEMBLY |
(a) Remove the rear No. 2 speaker assembly.
Click here
(b) Inspect the rear No. 2 speaker assembly.
Click here
OK:
Malfunction disappears.
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
|