| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001E8UM |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 08/2020] |
| Title: DOOR LOCK: REAR DOOR LOCK: INSTALLATION; 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020] | ||
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure below is for the LH side.
PROCEDURE
1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
(a) Attach the clamp and install the rear door inside locking cable assembly as shown in the illustration.
|
Install in this Direction |
2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
(a) Attach the clamp and install the rear door lock remote control cable assembly as shown in the illustration.
|
|
Install in this Direction |
3. INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH
|
(a) Attach the claw. |
|
(b) Attach the claw and install the rear door lock cover sub-assembly LH as shown in the illustration.
|
|
Install in this Direction |
4. INSTALL DOOR LOCK WIRING HARNESS SEAL
NOTICE:
- When reusing the removed rear door lock with motor assembly LH, be sure to replace the door lock wiring harness seal on the connector with a new one.
- Keep the door lock wiring harness seal of the connector free from grease and dust, etc.
- Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water to enter the connecting part. This may result in a malfunction of the rear door lock with motor assembly LH.
|
(a) When reusing rear door lock with motor assembly LH: (1) Install a new door lock wiring harness seal to the rear door lock with motor assembly LH. |
|
5. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY LH
(a) Apply MP grease to the sliding parts of the rear door lock with motor assembly LH.
(b) Connect the rear door lock with motor assembly LH to the release plate of the rear door outside handle frame sub-assembly LH, and set it to the rear door panel.
|
*a |
Release Plate |
|
|
Install in this Direction |
HINT:
Make sure that the release plate of the rear door outside handle frame sub-assembly LH is securely connected to the rear door lock with motor assembly LH.
(c) Using a T30 "TORX" socket wrench, install the front door lock with motor assembly LH with the 3 "TORX" screws.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
6. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Click here
![2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]; DOOR / HATCH: REAR DOOR: REASSEMBLY+](/t3Portal/stylegraphics/info.gif)
7. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
Click here
8. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
Click here
9. INSTALL REAR DOOR GLASS RUN LH
Click here
10. INSTALL REAR DOOR FRAME GARNISH LH
Click here
11. INSTALL REAR DOOR SERVICE HOLE COVER LH
Click here
12. INSTALL REAR DOOR REAR BELT SEAL LH
Click here
13. INSTALL REAR DOOR FRONT BELT SEAL LH
Click here
14. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH
Click here
15. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
16. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Click here
17. INSTALL DOOR ASSIST GRIP COVER LH
Click here
18. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH
Click here
19. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for A25A-FXS:
Click here
(b) for A25A-FKS:
Click here
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
20. INSTALL BATTERY HOLE COVER (for HV Model)
Click here
21. INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
22. INSTALL DECK BOARD ASSEMBLY (for HV Model)
Click here
23. INITIALIZE POWER WINDOW CONTROL SYSTEM
Click here
24. CHECK POWER WINDOW CONTROL SYSTEM
Click here
25. CHECK POWER DOOR LOCK CONTROL SYSTEM
Click here
|
|