Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001EKLN
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [11/2018 - 08/2020]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY): Pattern Select Switch Eco Mode Circuit; 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]

Pattern Select Switch Eco Mode Circuit

DESCRIPTION

When selecting ECO mode, the ECO mode switch (integration control and panel assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system and the hybrid vehicle control system.

WIRING DIAGRAM

PROCEDURE

1.

READ VALUE USING TECHSTREAM (CAN BUS CHECK)

Click here 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY): Pattern Select Switch EV Mode Circuit+

Result

Proceed to

All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.

A

None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.

B

B

GO TO CAN COMMUNICATION SYSTEM 2019 MY RAV4 HV [11/2018 - 02/2019]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): HOW TO PROCEED WITH TROUBLESHOOTING 2019 - 2024 MY RAV4 HV [02/2019 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): HOW TO PROCEED WITH TROUBLESHOOTING

A

2.

CHECK DTC OUTPUT (HEALTH CHECK)

Click here 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY): Pattern Select Switch EV Mode Circuit+

Result

Proceed to

No DTCs are output.

A

DTCs are output.

B

B

GO TO DTC CHART

A

3.

READ VALUE USING TECHSTREAM (ECO SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Enter the following menus: Body Electrical / Air Conditioner / Data List / ECO Switch.

Body Electrical > Air Conditioner > Data List

Tester Display

ECO Switch

(d) Read the value displayed on the Techstream.

Body Electrical > Air Conditioner > Data List

Tester Display

Measurement Item

Range

Normal Condition

ECO Switch

ECO mode switch (integration control and panel assembly) condition

ON or OFF

ECO mode switch (integration control and panel assembly) being pushed and held:

ON

ECO mode switch (integration control and panel assembly) not operated:

OFF

Result

Proceed to

The Techstream display changes according to the ECO mode switch (integration control and panel assembly) operation.

A

The Techstream display does not change according to the ECO mode switch (integration control and panel assembly) operation.

B

A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

4.

INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (ECO MODE)

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; HEATING / AIR CONDITIONING: COMBINATION SWITCH: INSPECTION 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; HEATING / AIR CONDITIONING: COMBINATION SWITCH: INSPECTION

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

OK

5.

CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - BODY GROUND)

(a) Disconnect the G32 ECO mode switch (integration control and panel assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G32-13 (GND) - Body ground

Always

Below 1 Ω

*a

Front view of wire harness connector

(to ECO Mode Switch (Integration Control and Panel Assembly))

(c) Reconnect the G32 ECO mode switch (integration control and panel assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))

(a) Disconnect the G46 air conditioning amplifier assembly connector.

(b) Disconnect the G32 ECO mode switch (integration control and panel assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G46-11 (ECOS) - G32-7 (ECU)

Always

Below 1 Ω

G46-11 (ECOS) or G32-7 (ECU) - Body ground

Always

10 kΩ or higher

*a

Front view of wire harness connector

(to Air Conditioning Amplifier Assembly)

*b

Front view of wire harness connector

(to ECO Mode Switch (Integration Control and Panel Assembly))

(d) Reconnect the G32 ECO mode switch (integration control and panel assembly) connector.

(e) Reconnect the G46 air conditioning amplifier assembly connector.

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR