Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001ENQW |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 - 02/2019] |
Title: WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR (for Front Door): REMOVAL; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Removal and installation of auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for HV model)
|
|
Reset back door close position
|
Power back door system (for HV model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
-
Power window regulator motor assembly LH
-
Power window regulator motor assembly RH
-
Front door window regulator sub-assembly LH
-
Front door window regulator sub-assembly RH
-
Front door glass sub-assembly LH
-
Front door glass sub-assembly RH
-
Front door glass run LH
-
Front door glass run RH
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Catch protection function
-
Remote control function
-
Wireless transmitter-linked function
-
Key-linked function
-
Key-off operation function
-
Window open warning function
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Entune system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Entune system and safety connect system
|
1 minute
|
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Removal and installation of auxiliary battery terminal
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for Gasoline model)*
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for Gasoline model)
|
|
Reset back door close position
|
Power back door system (for Gasoline model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
-
Power window regulator motor assembly LH
-
Power window regulator motor assembly RH
-
Front door window regulator sub-assembly LH
-
Front door window regulator sub-assembly RH
-
Front door glass sub-assembly LH
-
Front door glass sub-assembly RH
-
Front door glass run LH
-
Front door glass run RH
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Catch protection function
-
Remote control function
-
Wireless transmitter-linked function
-
Key-linked function
-
Key-off operation function
-
Window open warning function
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Entune system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Entune system and safety connect system
|
1 minute
|
HINT:
-
Use the same procedure for the RH and LH sides.
-
Use the same procedure described for the LH side.
-
Before performing disassembly work on the front door, make sure that the front door glass is fully open and be sure to disconnect the cable from the negative (-) auxiliary battery terminal.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
-
w/ Occupant Classification System:
Click here
-
w/o Occupant Classification System:
Click here
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE NO. 2 REAR FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for A25A-FXS:
Click here
(b) for A25A-FKS:
Click here
CAUTION:
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
-
If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
Click here
7. REMOVE FRONT DOOR ASSIST GRIP COVER LH
Click here
8. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Click here
9. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Click here
10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Click here
12. REMOVE FRONT DOOR FRONT BELT SEAL LH
Click here
13. REMOVE FRONT DOOR SERVICE HOLE COVER LH
Click here
14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Click here
15. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Click here
16. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
(a) Using a T25 "TORX" socket wrench, remove the 3 "TORX" screws and power window regulator motor assembly LH from the front door window regulator sub-assembly LH.
|
|
|