- Synchronize the vehicle information
- Initialization of the headlight ECU sub-assembly LH
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001EPED |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 02/2019] |
| Title: LIGHTING (EXT): HEADLIGHT ASSEMBLY (for Triple Beam Headlight): REMOVAL; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are installed, removed or replaced during the headlight assembly LH removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
w/ Headlight ECU: Headlight ECU sub-assembly LH |
|
Automatic headlight beam level control system |
|
|
Front bumper assembly (Including removal and installation) |
Front television camera view adjustment |
Panoramic view monitor system (for Gasoline model) |
|
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
Headlight ECU sub-assembly LH |
|
Automatic headlight beam level control system |
|
|
Front bumper assembly (Including removal and installation) |
Front television camera view adjustment |
Panoramic view monitor system (for HV model) |
|
NOTICE:
Even if the headlight ECU sub-assembly RH is replaced with a new one, synchronize the vehicle information and initialization are not necessary.
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. REMOVE FRONT BUMPER ASSEMBLY
-
except Off Road Package:
Click here
![2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; EXTERIOR PANELS / TRIM: FRONT BUMPER (except Off Road Package): REMOVAL](/t3Portal/stylegraphics/info.gif)
-
for Off Road Package:
Click here
2. REMOVE HEADLIGHT ASSEMBLY LH (w/o Headlight ECU)
(a) Apply protective tape as shown in the illustration.
|
Screw |
|
Bolt |
|
Protective Tape |
(b) Remove the 3 screws and bolt.
(c) Place your hand on 2 brackets of the headlight assembly LH to disconnect them from the screw seats.
|
*a |
Lower Bracket |
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
NOTICE:
Be careful not to break the bracket.
(d) Slide the headlight assembly LH in the direction indicated by the arrow (1) and detach the guide and lower bracket.
(e) Slide the headlight assembly LH in the direction indicated by the arrow (2) to remove it.
|
(f) Detach the 2 wire harness clamps and disconnect the 3 connectors. |
|
3. REMOVE HEADLIGHT ASSEMBLY LH (w/ Headlight ECU)
(a) Apply protective tape as shown in the illustration.
|
|
Screw |
|
|
Bolt |
|
|
Protective Tape |
(b) Remove the 3 screws and bolt.
(c) Place your hand on 2 brackets of the headlight assembly LH to disconnect them from the screw seats.
NOTICE:
Be careful not to break the bracket.
|
*a |
Lower Bracket |
|
*b |
Connector Lock Lever |
|
|
Place Hands Here |
|
|
Remove in this Direction (1) |
|
|
Remove in this Direction (2) |
(d) Slide the headlight assembly LH in the direction indicated by the arrow (1) and detach the guide and lower bracket.
(e) Slide the headlight assembly LH in the direction indicated by the arrow (2) to remove it.
(f) Release the connector lock lever and disconnect the connector under the headlight assembly LH.
|
|