for UB80E:
-
If transaxle compensation code read from ECM
- Perform reset memory
- Transfer transaxle compensation code
- Perform road test to allow ECM to learn
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001EV9E |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 08/2020] |
| Title: A25A-FKS (ENGINE CONTROL): ACTIVE CONTROL ENGINE MOUNT (for Rear Side): REMOVAL; 2019 - 2020 MY RAV4 [11/2018 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear engine mounting insulator removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Battery terminal is disconnected/reconnected |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Replacement of ECM |
Perform Vehicle Identification Number (VIN) or frame number registration |
DTC P063051 is output |
w/ Canister Pump Module:
w/o Canister Pump Module:
|
|
Code registration |
Engine start function |
See Service Bulletin for the registration method. |
|
|
|
|
for Initialization:
for Registration:
|
|
for UB80E:
|
|||
for UB80F:
|
|
for Initialization:
for Registration:
|
|
for UB80F:
|
|||
|
Gas leak from exhaust system is repaired |
Inspection After Repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
|
Suspension, tires, etc. |
Television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
|
Parking assist ECU initialization |
Panoramic view monitor system (for Gasoline model) |
|
|
|
Front wheel alignment adjustment |
|
|
|
|
Front bumper assembly (Including removal and installation) |
Front television camera view adjustment |
Panoramic view monitor system (for Gasoline model) |
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
PROCEDURE
1. REMOVE FRONT FRAME ASSEMBLY
Click here
![2019 MY RAV4 [11/2018 - 10/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE REAR ENGINE MOUNTING INSULATOR
|
(a) Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket. |
|
|
(b) Remove the bolt and wire harness clamp bracket from the rear engine mounting insulator. |
|
|
(c) Detach the clamp and remove the vacuum hose from the rear engine mounting insulator. |
|
|
|