A25A-FXS (LUBRICATION): OIL PUMP: REMOVAL; 2019 MY RAV4 HV [11/2018

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001FFYG
Model Year Start: 2019	Model: RAV4 HV	Prod Date Range: [11/2018 - 02/2019]
Title: A25A-FXS (LUBRICATION): OIL PUMP: REMOVAL; 2019 MY RAV4 HV [11/2018 - 02/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane control system
	Perform steering sensor zero point calibration	Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for HV model)
	Reset back door close position	Power back door system (for HV model)
	Back door lock initialization	Power door lock control system
Replacement of ECM	Perform Vehicle Identification Number (VIN) registration	DTC P063051 is output
Replacement of engine assembly Gas leak from exhaust system is repaired Replacement of throttle body with motor assembly Replacement of cam timing control motor with EDU assembly Removal and installation of a cam timing control motor with EDU assembly Replacement of camshaft timing gear assembly Removal and installation of a camshaft timing gear assembly Replacement of cylinder head sub-assembly Replacement of camshaft (for intake or exhaust camshaft) Replacement of camshaft timing exhaust gear assembly Replacement of port fuel injector assembly Replacement of direct fuel injector assembly Replacement of fuel pump assembly (for high pressure side) Replacement of engine coolant temperature sensor Replacement of spark plug Replacement of ignition coil assembly Replacement of EGR valve assembly Replacement of knock control sensor Replacement of air fuel ratio sensor (sensor 2)	Inspection after repair	Poor idle, etc. Engine start function, etc.
Replacement of inverter with converter assembly	Resolver learning	DTCs are stored Slight vibration at a vehicle speed of 5 km/h (3 mph) or less Shock or vibration during acceleration
Replacement of hybrid vehicle transaxle assembly	Resolver learning Initialize resolver
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Television camera assembly optical axis (Back camera position setting)	Parking assist monitor system
	Parking assist ECU initialization Adjust steering angle	Panoramic view monitor system (for HV model)
Replacement of headlight ECU sub-assembly LH	Synchronize the vehicle information Perform headlight ECU sub-assembly LH initialization	Lighting system (EXT)(w/ Headlight ECU)
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Perform headlight ECU sub-assembly LH initialization	Lighting system (EXT)(w/ Headlight ECU)
Front wheel alignment adjustment	Clear the zero point calibration data and stored linear solenoid valve calibration data. Perform initialization and calibration of the linear solenoid valve. Perform yaw rate and acceleration sensor zero point calibration.	DTCs are stored ABS warning light illuminates Brake warning light / yellow (minor malfunction) illuminates Slip indicator light illuminates VSC disabled or malfunctions
Front bumper assembly (Including removal and installation)	Front television camera view adjustment	Panoramic view monitor system (for HV model)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Entune system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Entune system and safety connect system	1 minute

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here

PROCEDURE

1. REMOVE TIMING CHAIN COVER ASSEMBLY

Click here

2. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Click here

3. REMOVE OIL STRAINER SUB-ASSEMBLY

Click here

4. REMOVE ENGINE OIL LEVEL SENSOR

Click here

5. REMOVE OIL PUMP BRACKET

Click here

6. REMOVE ENGINE BALANCER ASSEMBLY

Click here

7. REMOVE OIL PUMP ASSEMBLY

(a) Remove the 3 bolts and oil pump assembly from the stiffening crankcase assembly.

8. REMOVE STIFFENING CRANKCASE ASSEMBLY

Click here