AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION; 2019 MY RAV4 RAV4 HV [11/2018

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001FHCT
Model Year Start: 2019	Model: RAV4	Prod Date Range: [11/2018 - 02/2019]
Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.

PROCEDURE

1. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

(a) Secure the steering knuckle between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.

(b) Install the front axle hub sub-assembly and front disc brake dust cover to the steering knuckle with the 4 bolts.

Torque:

120 N·m {1224 kgf·cm, 89 ft·lbf}

NOTICE:

Be careful not to damage the speed sensor rotor or contact surfaces.
Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.

2. INSTALL FRONT AXLE ASSEMBLY

(a) Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.

Toyota Body Grease W

(b) Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:

290 N·m {2957 kgf·cm, 214 ft·lbf}

NOTICE:

Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.
When installing the nuts, keep the bolts from rotating.

HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.

3. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

(a) Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and connect the front drive shaft assembly to the front axle assembly.

NOTICE:

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.
Check that there is no foreign matter on the speed sensor rotor or contact surfaces.
Do not damage the front drive shaft outboard joint boot.
Do not damage the front disc brake dust cover.
Do not damage the speed sensor rotor.

Matchmark

4. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

(a) Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:

92 N·m {938 kgf·cm, 68 ft·lbf}

5. CONNECT TIE ROD ASSEMBLY LH

Click here

6. INSTALL FRONT DISC

Click here

7. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

Click here

8. INSTALL FRONT AXLE SHAFT NUT LH

(a) Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:

Be sure to perform this work even when using a new front drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.

(b) Using a 30 mm deep socket wrench, while applying the brakes, temporarily install the front axle shaft nut.

Torque:

294 N·m {2998 kgf·cm, 217 ft·lbf}

NOTICE:

Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.

HINT:

Keep depressing the brake pedal to prevent the front drive shaft from rotating.

9. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

Click here

10. REMOVE FRONT DISC

Click here

11. INSPECT FRONT AXLE HUB BEARING LOOSENESS

Click here

12. INSPECT FRONT AXLE HUB RUNOUT

Click here

13. INSTALL FRONT DISC

Click here

14. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

Click here

15. INSTALL FRONT SPEED SENSOR LH

(a) Set the 2 front speed sensor LH hooks on the front shock absorber assembly LH.

Hook

NOTICE:

Do not twist the front speed sensor when installing it.

(b) Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

NOTICE:

Do not twist the front flexible hose when installing it.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

NOTICE:

Prevent foreign matter from attaching to the front speed sensor tip.
Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.
After installing the front speed sensor to the steering knuckle, make sure that there is no clearance between the front speed sensor stay and steering knuckle. Also make sure that no foreign matter is stuck between the parts.
Do not twist the front speed sensor when installing it.

(d) Engage the clamp.

NOTICE:

Do not twist the front speed sensor when installing it.

16. STAKE FRONT AXLE SHAFT NUT LH

(a) Using a chisel and hammer, stake the front axle shaft nut.

17. INSTALL FRONT WHEEL

Click here

18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

(a) Connect the reservoir level switch connector.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

Click here

(1) Turn the ignition switch on (READY).

(2) Depress the brake pedal and release it.

(3) Clear the DTCs.

Click here

19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Click here

20. CHECK FOR SPEED SENSOR SIGNAL

w/ Vacuum Brake Booster: Click here
w/o Vacuum Brake Booster: Click here

21. PERFORM INITIALIZATION

for HV Model:

Parking assist monitor system
Panoramic view monitor system (for HV model)
Lighting system (EXT)(w/ Headlight ECU)

for Gasoline Model:

Parking support brake system (for Gasoline model)
Parking assist monitor system
Panoramic view monitor system (for Gasoline model)
Lighting system (EXT)(w/ Headlight ECU)