| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FHLY |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [11/2018 - 08/2020] |
| Title: A25A-FXS (FUEL): FUEL PUMP (w/o Canister Pump Module): INSTALLATION; 2019 - 2020 MY RAV4 HV [11/2018 - 08/2020] | ||
INSTALLATION
PROCEDURE
1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
(a) Install a new gasket to the fuel tank assembly.
(b) Set the fuel suction with pump and gauge tube assembly to the fuel tank assembly.
NOTICE:
- Be careful not to bend the arm of the fuel sender gauge assembly.
- To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.
|
*1 |
Plate Sub-assembly |
*2 |
Fuel Sub-tank Sub-assembly |
|
*3 |
Fuel Sender Gauge Assembly |
- |
- |
|
(c) Align the protrusions of the fuel suction with pump and gauge tube assembly with the notches in the fuel tank assembly. |
|
2. INSTALL FUEL PUMP GAUGE RETAINER
(a) Install the fuel pump gauge retainer.
(1) While pressing down on the fuel suction with pump and gauge tube assembly, temporarily install the fuel pump gauge retainer.
|
(2) Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer. SST: 09808-14031 09808-01030 09808-01090 SST: 09808-01071 HINT: Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer. |
|
(3) While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
|
(4) Install SST (handle) and an extension bar to SST (plate). SST: 09808-14031 09808-01010 09808-01030 09808-01090 SST: 09808-01071 |
|
(5) Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction with pump and gauge tube assembly to the fuel tank assembly.
CAUTION:
When turning SST (handle), take care not to hit the console box assembly with your hands or SST (handle).
NOTICE:
- Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
- Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
- Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
- Do not spin SST too fast or use an impact wrench as this may result in damage to components.
- If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
- Make sure that the fuel suction tube set gasket does not come off.
(b) Attach the claw and install the No. 1 fuel tube clamp to the fuel pump gauge retainer.
3. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
(a) Push the fuel tube joint of the fuel tank main tube sub-assembly, and install the tube joint clip.
NOTICE:
- Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
- Check that the fuel tube joint is securely inserted to the end.
- Check that the tube joint clip is on the collar of the fuel tube joint.
- After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.
|
*1 |
Tube Joint Clip |
|
*a |
Nylon Tube |
|
*b |
Fuel Tube Joint |
|
*c |
O-ring |
|
*d |
Correct |
|
*e |
Incorrect |
4. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
(a) Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction with pump and gauge tube assembly.
Click here
![2019 MY RAV4 HV [11/2018 - 02/2019]; A25A-FXS (FUEL): FUEL SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
5. INSTALL REAR FLOOR SERVICE HOLE COVER
(a) Connect the 2 connectors to the fuel suction with pump and gauge tube assembly.
(b) Install the rear floor service hole cover with the 3 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
6. INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY
Click here
7. INSTALL BATTERY SERVICE COVER BOARD
Click here
8. INSTALL NO. 2 BATTERY SERVICE COVER BOARD
Click here
9. INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
10. INSTALL NO. 3 BATTERY SERVICE COVER BOARD
Click here
11. INSTALL REAR DOOR SCUFF PLATE LH
Click here
12. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here
13. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
Click here
14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
15. INSTALL BATTERY HOLE COVER
Click here
16. INSTALL REAR NO. 2 FLOOR BOARD
Click here
17. INSTALL DECK BOARD ASSEMBLY
Click here
18. INSPECT FOR FUEL LEAK
Click here
19. PERFORM INITIALIZATION
(a) Perform "Inspection After Repair" after replacing the fuel pump.
Click here
|
|