INSTALLATION

PROCEDURE

1. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

(a) Attach the 4 clips and install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly.

2. INSTALL NO. 1 FUEL TANK CUSHION

(a) Install 2 new No. 1 fuel tank cushions to the fuel tank assembly.

3. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

(a) Attach the clamp and install the fuel tank main tube sub-assembly to the fuel tank assembly.

4. INSTALL FUEL TANK ASSEMBLY

CAUTION:

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

(a) Set the fuel tank assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.

(b) Using the engine lifter, slowly raise the fuel tank assembly, and temporarily install the fuel tank assembly and 2 fuel tank band sub-assemblies with the 2 bolts in the order shown in the illustration. NOTICE: Be careful not to drop the fuel tank assembly. When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.

(c) Using SST, tighten the 4 bolts in the order shown in the illustration.

SST: 09961-00950

Torque:

Specified tightening torque

45 N*m (459 kgf*cm, 33 ft.*lbf)

5. CONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY

(a) Connect the fuel tank filler pipe sub-assembly to the fuel tank filler pipe assembly.

Click here

6. CONNECT FUEL TANK BREATHER TUBE

(a) Connect the fuel tank breather tube to the fuel tank filler pipe assembly.

Click here

7. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

(a) Connect the fuel tank main tube sub-assembly to the fuel tube.

Click here

8. CONNECT FUEL TANK VENT TUBE

(a) Attach the clamp and connect the fuel tank vent tube.

(b) Connect the fuel tank vent tube to the fuel tank vent hose sub-assembly.

Click here

9. INSTALL NO. 1 FUEL TANK PROTECTOR

(a) Install the No. 1 fuel tank protector to the fuel tank band with the 2 nuts.

Torque:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

10. INSTALL NO. 1 FLOOR UNDER COVER

(a) Install the No. 1 floor under cover to the body and tighten the nut.

(b) Attach the 3 clips and install the 2 bolts.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

11. INSTALL FRONT FLOOR COVER RH

(a) Install the front floor cover RH to the body and tighten the 3 nuts.

(b) Attach the 2 clips and install the 2 bolts and 4 screws.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

12. INSTALL NO. 2 FLOOR UNDER COVER

(a) Install the No. 2 floor under cover to the body and tighten the 4 nuts.

(b) Attach the 3 clips and install the 2 bolts.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

13. INSTALL FRONT FLOOR COVER LH

(a) Install the front floor cover LH to the body and tighten the 3 nuts.

(b) Attach the 3 clips and install the 2 bolts and 5 screws.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

14. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here

15. INSTALL NO. 1 ENGINE UNDER COVER

Click here

16. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Click here

17. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Click here

18. INSTALL PROPELLER SHAFT ASSEMBLY (for AWD)

Click here

19. INSTALL TAIL EXHAUST PIPE ASSEMBLY

Click here

20. ADD FUEL

21. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Click here

22. INSTALL FUEL TANK VENT TUBE ASSEMBLY

Click here

23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here