Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001FMPE
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 08/2020]
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P032515; Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open; 2019 - 2020 MY RAV4 [11/2018 - 08/2020]

DTC

P032515

Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open

DESCRIPTION

Refer to DTC P032511.

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P032511; Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground+

HINT:

When DTC P032515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P032515

Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open

The knock control sensor output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic).
  • Open or short in knock control sensor circuit
  • Knock control sensor
  • ECM

Comes on

DTC stored

SAE Code: P0328

Reference: Inspection using an oscilloscope.

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P032511; Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground

MONITOR DESCRIPTION

If the output voltage transmitted by the knock control sensor remains high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Frequency of Operation

Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Start the engine and wait 5 minutes.
  7. Turn the Techstream on.
  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P032515.
  12. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P032511.

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): P032511; Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground+

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)

*a

Front view of wire harness connector

(to Knock Control Sensor)

(a) Disconnect the knock control sensor connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

F3-2 (KNK1) - F3-1 (EKNK)

Ignition switch ON

4.5 to 5.5 V
NG

GO TO STEP 3

OK

2.

INSPECT KNOCK CONTROL SENSOR

(a) Inspect the knock control sensor.

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; A25A-FKS (ENGINE CONTROL): KNOCK SENSOR: INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the knock control sensor.

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): INITIALIZATION

OK

GO TO STEP 4

NG

REPLACE KNOCK CONTROL SENSOR

3.

CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)

(a) Disconnect the knock control sensor connector.

(b) Disconnect the ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F3-2 (KNK1) - C40-111 (KNK1)

Always

Below 1 Ω

F3-1 (EKNK) - C40-112 (EKNK)

Always

Below 1 Ω

F3-2 (KNK1) - C40-111 (KNK1) - Other terminals

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

5.

CHECK WHETHER DTC OUTPUT RECURS (DTC P032515)

(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(b) Enter the following menus: Powertrain / Engine / Trouble Codes.

(c) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P032515 is output

B
A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM