| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FQNW |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [11/2018 - 10/2023] |
| Title: DOOR / HATCH: POWER BACK DOOR SYSTEM (for HV Model): OPERATION CHECK; 2019 - 2023 MY RAV4 HV [11/2018 - 10/2023] | ||
OPERATION CHECK
OPERATION CONDITION
NOTICE:
-
This check is possible only when the "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "On" (The default setting is "On").
Click here
![2019 - 2023 MY RAV4 HV [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for HV Model): CUSTOMIZE PARAMETERS](/t3Portal/stylegraphics/info.gif)
- Before performing an operation check, check that the power back door system customization is set to its default setting.
(a) Conditions necessary for the power back door to open:
- The back door is unlocked (except wireless one motion function).*
- The vehicle speed is 3 km/h (2 mph) or less (only when the power switch is on [IG]).
- The shift lever is in P, the brake pedal is depressed or the parking brake lever is pulled up (this can be determined only when the power switch is on [IG]).
- *: Depending on the customize settings, the back door may not unlock and only the driver door unlocks when the first unlock operation is performed. Check that the customize settings in the table below are set to "OFF", and check that the back door unlocks.
|
Tester Display |
Link |
|---|---|
|
Unlock Key Twice |
|
|
Unlock 2 Opeartion |
|
CHECK BASIC OPERATION
(a) Check the opening operation.
(1) With the back door fully closed, push the power back door control switch and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
(2) With the back door fully closed, push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
(3) With the back door fully closed, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
(b) Check the close operation.
(1) With the back door fully open, push the power back door control switch and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.
(2) With the back door fully open, push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.
(3) With the back door fully open, push the No. 1 power back door control switch and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.
- *: w/ Hands Free Power Back Door
CHECK OPERATION WHEN ANOTHER INPUT DETECTED DURING OPEN AND CLOSE OPERATIONS
(a) Check operation when another input detected during open operations
(1) During a power back door opening operation, push the power back door control switch and check that the power back door warning buzzer and wireless door lock buzzer sound for 0.2 seconds, the hazard warning lights flash twice and the back door opening operation stops.
After the opening operation stops, press the power back door control switch again and check that the power back door operates until it reaches the fully closed position.
(2) During a power back door opening operation, push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer and wireless door lock buzzer sound for 0.2 seconds, the hazard warning lights flash twice and the back door opening operation stops.
After the opening operation stops, push the electrical key transmitter sub-assembly (electrical key) again and check that the power back door operates until it reaches the fully closed position.
(3) During a power back door opening operation, push the No. 1 power back door control switch and check that the power back door warning buzzer sound for 0.2 seconds, the hazard warning lights flash twice and the power back door opening operation stops.
After the opening operation stops, push the No. 1 power back door control switch again and check that the power back door operates until it reaches the fully closed position.
(4) During a power back door opening or closing operation, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.2 seconds, the hazard warning lights flash twice and the power back door opening operation stops.
After the opening operation stops, push the back door opener switch assembly again and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(5) During a power back door opening operation, perform a kick operation and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops.*
After the opening operation stops, kick operation again and check that the power back door operates until it reaches the fully closed position.*
(b) Check operation when another input detected during close operations
(1) During a power back door closing operation, push the power back door control switch and check that the power back door warning buzzer and wireless door lock buzzer sound for 0.2 seconds and the back door stops.
After the closing operation stops, press the power back door control switch again and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(2) During a power back door closing operation, push the electrical key transmitter sub-assembly (electrical key) again and check that the power back door warning buzzer and wireless door lock buzzer sound for 0.2 seconds and the back door stops.
After the closing operation stops, press the electrical key transmitter sub-assembly (electrical key) again and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(3) During a power back door closing operation, push the No. 1 power back door control switch again and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door closing operation stops.
After the closing operation stops, push the No. 1 power back door control switch again and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(4) During a power back door closing operation, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door closing operation stops.
After the closing operation stops, push the back door opener switch assembly again and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.
(5) During a power back door closing operation, perform a kick operation and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops.*
After the closing operation stops, kick operation again and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.*
CHECK WIRELESS ONE MOTION FUNCTION
NOTICE:
- Before performing an operation check, check that the power back door system customization is set to its default setting.
-
This check is possible only when the "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "On" (The default setting is "On").
Click here
-
This check is possible only when the "Wireless Power Back Door Open" customization setting using the Techstream is set to "Lock:Twice/Unlock:Twice" or "Lock:0.8s/Unlock:0.8s" (The default setting is "Lock:OFF/Unlock:OFF" or "Lock:0.8s/Unlock:0.8s").
Click here
(a) Check the wireless one motion operation.
(1) With all doors locked, push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.
CHECK JAM PROTECTION FUNCTION
HINT:
- The multiplex network door ECU detects changes in the operating speed of the back door while the power back door is operating. If a change in the operating speed is out of the normal range, it will be judged that foreign objects are in the path of the power back door and the operation will stop if the door is operating in the opening direction or move a certain amount in the reverse direction if the door is operating in the closing direction.
- When the power back door sensor assemblies built into both sides of the back door are compressed, it is judged that foreign objects are in the path of the power back door and the operation will reverse a little in the opposite direction and then stop.
- The power back door sensor assemblies operate only while the back door is closing. They do not operate while the back door is opening.
(a) Check the jam protection function (the power back door sensor assembly) while the power back door is closing.
NOTICE:
Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.
(1) Fully open the back door.
(2) Press a switch to close the power back door.
(3) While the back door is closing, press a power back door sensor assembly using the handle of a hammer or equivalent.
(4) Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door reverses a certain amount and stops.
(b) Check the jam protection function (the pulse sensor in the multiplex network door ECU) while the power back door is closing.
NOTICE:
Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.
(1) Fully open the back door.
(2) Press a switch to close the power back door.
(3) While the back door is closing, insert a tire or equivalent between the door panel and vehicle body, in order to interrupt the closing operation.
(4) Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door reverses a certain amount and stops.
(c) Check the jam protection function while the power back door is opening.
NOTICE:
Pay thorough attention that your body or your clothes, etc. do not get caught in the door by accident in this process.
(1) Fully close the back door.
(2) Press a switch to open the power back door.
(3) While the back door is opening, use your hands to press on the outside surface of the back door panel so that the operating speed decreases.
(4) Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door stops.
CHECK ASSIST OPERATION
(a) Check that the door automatically starts to fully close when the door is manually moved in the closing direction with the back door at rest.
CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When not using Techstream)
(a) Register open operation automatic stopped position in memory
(1) Open the back door by operating each switch.
(2) Operate each switch to stop the open operation when the back door reaches the desired automatic stopped position.
(3) When the No. 1 power back door control switch is pressed and held for 2 seconds or more with the back door at the stopped position, the buzzer sounds 4 times and the system memorizes the automatic stopped position for the open operation.
(4) Check that the back door stops at the memorized position when an open operation is performed with each switch.
(b) Clear open operation automatic stopped position memory
(1) Open the back door by operating each switch.
(2) Stop the back door by operating each switch.
(3) When the No. 1 power back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.
CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using Techstream)
(a) Register open operation automatic stopped position in memory
(1) Using the Techstream, select the "Power Back Door Opening Adjust" customize setting.
Click here
(2) According to the Techstream display, set the customize setting.
(3) Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.
(b) Clear open operation automatic stopped position memory
(1) Open the back door by operating each switch.
(2) Stop the back door by operating each switch.
(3) When the No. 1 power back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.
CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using Multi-information display)
(a) Register open operation automatic stopped position in memory
(1) Using the multi-information display, select the "Opening Adjustment" customize setting.
Click here
(2) According to the screen display, set the customize setting.
(3) Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.
(b) Clear open operation automatic stopped position memory
(1) Open the back door by operating each switch.
(2) Stop the back door by operating each switch.
(3) When the No. 1 power back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.
CHECK HANDS FREE POWER BACK DOOR OPERATION (w/ Hands Free Power Back Door)
NOTICE:
-
This function operates when the "Kick Sensor Function" item is set to "ON" using the Techstream customization function (The default setting is "ON").
Click here
-
This function operates when the "Kick Sensor" item is set to "On" using the customization function via the multi-information display in the combination meter assembly (The default setting is "On").
Click here
-
This function operates when the "Kick Sensor Operation with ACC ON" item is set to "Not Available" using the Techstream customization function (The default setting is "Not Available").
Click here
(a) With the power switch off or power switch on (ACC) and the electrical key transmitter sub-assembly (electrical key) being carried, check that the power back door operates when a kick operation is performed within 100 mm (3.94 in.) of the rear bumper surface.
|
*1 |
Kick Door Control Sensor |
- |
- |
|
*a |
100 mm (3.94 in.) |
*b |
Center of the rear bumper |
HINT:
- The hands free power back door detects a change in electrostatic capacitance in the detection area of the kick door control sensor (Operation trigger).
- Placing your leg or a metallic object within 100 mm (3.94 in.) of the rear bumper surface and then moving it out of the detection area results in the hands free power back door operating due to the kick door control sensor detecting a change in electrostatic capacitance.
- The kick door control sensor receives vehicle speed, IG and ACC signals from the main body ECU (multiplex network body ECU) via LIN communication and uses the information to stop sensor oscillation.
|
|