| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001FRDY |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 10/2022] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING; 2019 - 2022 MY RAV4 [11/2018 - 10/2022] | ||
|
HOW TO PROCEED WITH TROUBLESHOOTING |
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the panoramic view monitor system.
- *: Use the Techstream.
PROCEDURE
|
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
|
2. |
CUSTOMER PROBLEM ANALYSIS |
(a) Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
HINT:
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
|
Problem Symptom |
Cause |
|---|---|
|
The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. |
The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
|
|
3. |
INSPECT BATTERY VOLTAGE |
(a) Measure the battery voltage.
Standard voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding.
|
|
4. |
SYSTEM CHECK |
(a) Check the vehicle specification.
|
Result |
Proceed to |
|---|---|
|
w/ Navigation System |
A |
|
w/ Audio and Visual System |
B |
| B |
|
|
|
5. |
CHECK NAVIGATION SYSTEM |
(a) Refer to the navigation system.
Click here
![2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PROBLEM SYMPTOMS TABLE](/t3Portal/stylegraphics/info.gif)
OK:
Navigation system is normal.
|
Result |
Proceed to |
|---|---|
|
Navigation system is normal |
A |
|
Navigation system is abnormal |
B |
| A |
|
| B |
|
|
6. |
CHECK AUDIO AND VISUAL SYSTEM |
(a) Refer to the audio and visual system.
Click here
OK:
Audio and visual system is normal.
|
Result |
Proceed to |
|---|---|
|
Audio and visual system is normal |
A |
|
Audio and visual system is abnormal |
B |
| B |
|
GO TO AUDIO AND VISUAL SYSTEM
|
|
|
7. |
CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
|
Result |
Proceed to |
|---|---|
|
CAN DTCs are not output |
A |
|
CAN DTCs are output |
B |
| B |
|
|
|
8. |
CHECK FOR DTC* |
(a) Check for DTCs and note any codes that are output.
Click here
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
(b) Clear the DTCs.
Click here
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
(c) Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.
Click here
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC is not output |
A |
|
DTC is output |
B |
| B |
|
GO TO DIAGNOSTIC TROUBLE CODE CHART
|
|
|
9. |
PROBLEM SYMPTOMS TABLE |
(a) Refer to the Problem Symptoms Table.
Click here
|
Result |
Proceed to |
|---|---|
|
Fault is not listed in Problem Symptoms Table |
A |
|
Fault is listed in Problem Symptoms Table |
B |
| B |
|
|
|
10. |
OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Data List / Active Test
Click here
(b) Terminals of ECU
Click here
|
|
11. |
ADJUST, REPAIR OR REPLACE |
|
|
12. |
CONFIRMATION TEST |
| NEXT |
|
END |
|
|