Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001FYQQ |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 -
] |
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): Main Body ECU Communication Stop Mode; 2019 - 2024 MY RAV4 [11/2018 - ] |
Main Body ECU Communication Stop Mode
|
DESCRIPTION
Detection Item
|
Symptom
|
Trouble Area
|
Main Body ECU Communication Stop Mode
|
Any of the following conditions are met:
|
-
Main body ECU (multiplex network body ECU) branch wire or connector
-
Power source circuit of main body ECU (multiplex network body ECU) or instrument panel junction block assembly
-
Main body ECU (multiplex network body ECU) or instrument panel junction block assembly ground circuit
-
Main body ECU (multiplex network body ECU)
-
Instrument panel junction block assembly
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
-
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
-
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
1.
|
CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] BRANCH WIRE)
|
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the main body ECU (multiplex network body ECU) connector.
|
|
*a
|
Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
|
|
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G44-5 (CANH) - G44-4 (CANL)
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
NG |
|
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
|
(a) Remove the main body ECU (multiplex network body ECU).
Click here
(b) Connect the instrument panel junction block assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-11 (GND1) - Body ground
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
|
|
*a
|
Component without harness connected
(Instrument Panel Junction Block Assembly)
|
|
|
(d) Reconnect the cable to the negative (-) battery terminal.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
A-31 (BECU) - Body ground
|
Always
|
11 to 14 V
|
A-30 (ACC) - Body ground
|
Ignition switch ACC
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
A-32 (IG) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
NG
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
|
(a) Disconnect the instrument panel junction block assembly connectors.
*a
|
Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
|
-
|
-
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
4D-3 - Body ground
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
4K-1 - Body ground
|
Always
|
11 to 14 V
|
4F-1 - Body ground
|
Always
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
|
(a) Disconnect the instrument panel junction block assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
4A-30 - Body ground
|
Ignition switch ACC
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
4A-17 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
|
|
*a
|
Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
|
|
|
Result
|
Proceed to
|
OK
|
A
|
NG (w/ Smart Key System)
|
B
|
NG (w/o Smart Key System)
|
C
|
C |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|