Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G1YK |
Model Year Start: 2019 |
Model: RAV4 HV |
Prod Date Range: [11/2018 -
] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): B27A8; Open in Outside Luggage Compartment Electrical Key Antenna Circuit; 2019 - 2024 MY RAV4 HV [11/2018 - ] |
DTC
|
B27A8
|
Open in Outside Luggage Compartment Electrical Key Antenna Circuit
|
DESCRIPTION
The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage compartment). For the electrical key antenna (outside luggage compartment) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Note
|
B27A8
|
Open in Outside Luggage Compartment Electrical Key Antenna Circuit
|
An open is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
|
-
Certification ECU (smart key ECU assembly)
-
Electrical key antenna (outside luggage compartment)
-
Harness or connector
|
DTC Output Confirmation Operation:
|
-
*: Only output while a malfunction is present and the power switch is on (IG).
Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected
|
Fail-safe Operation when Malfunction Detected
|
Entry lock/unlock operation cannot be performed for back door
|
-
|
Related Data List and Active Test
DTC No.
|
Data List and Active Test
|
B27A8
|
Key diagnostic mode can be used to perform troubleshooting
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
CHECK CONNECTOR CONNECTION
|
(a) Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment).
OK:
Connectors are properly connected.
NG |
|
CONNECT CONNECTORS PROPERLY
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
|
(a) Disconnect the M7 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the Q15 electrical key antenna (outside luggage compartment) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
M7-13 (CLG8) - Q15-2 (ANTE8)
|
Always
|
Below 1 Ω
|
M7-12 (CG8B) - Q15-1 (CLGB)
|
Always
|
Below 1 Ω
|
(d) Reconnect the M7 certification ECU (smart key ECU assembly) connector.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
|
*a
|
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
|
*b
|
Waveform 1
|
(a) Using an oscilloscope, check the waveform.
OK:
Tester Connection
|
Condition
|
Tool Setting
|
Specified Condition
|
M7-13 (CLG8) - G54-18 (E)
|
Procedure:
-
Power switch off
-
Electrical key transmitter sub-assembly brought outside vehicle
-
All doors closed
-
Back door opener switch assembly off → on
|
2 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 1)
|
M7-12 (CG8B) - G54-18 (E)
|
Procedure:
-
Power switch off
-
Electrical key transmitter sub-assembly brought outside vehicle
-
All doors closed
-
Back door opener switch assembly off → on
|
2 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 1)
|
|