Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G20W |
Model Year Start: 2019 |
Model: RAV4 HV |
Prod Date Range: [11/2018 -
] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): B2779; Engine Starter Communication Malfunction; 2019 - 2024 MY RAV4 HV [11/2018 - ] |
DTC
|
B2779
|
Engine Starter Communication Malfunction
|
DESCRIPTION
If the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly) or the remote engine start ID is not registered*, this DTC is stored.
If communication between the remote engine start ECU and the certification ECU (smart key ECU assembly) is established and the remote engine start is operated, this DTC and the corresponding history DTC will be cleared.
HINT:
*: Registration status of the remote engine start ECU ID can be checked using the "Wireless C Code" item in the Data List.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Note
|
B2779
|
Engine Starter Communication Malfunction
|
When the remote engine start is operated to try to turn the power source on, or start the engine, the remote start function tries to communicate with the certification ECU (smart key ECU assembly), but communication fails. (1 trip detection logic*)
|
-
CAN communication system
-
Remote start ECU (genuine part)
-
Main body ECU (multiplex network body ECU)
-
Certification ECU (smart key ECU assembly)
|
DTC output confirmation operation:
|
-
*: Only detected while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected
|
Fail-safe Operation when Malfunction Detected
|
The hybrid control system cannot be started with a remote start operation
|
The hybrid control system cannot be started with a remote start operation only
|
Related Data List and Active Test
DTC No.
|
Data List and Active Test
|
B2779
|
Smart Key
-
Wireless Starter Com ID
-
Wireless C Code
|
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
CHECK CAN COMMUNICATION SYSTEM
|
(a) Check for CAN communication system DTCs.
Click here
OK:
CAN communication DTCs are not output.
OK
|
|
|
2.
|
READ VALUE USING TECHSTREAM (WIRELESS C CODE)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Wireless C Code
|
Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly)
|
No Regd or Regd
|
No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly)
Regd: Remote starter ID registered to remote engine start ECU and certification ECU (smart key ECU assembly)
|
Problems may be caused by the following:
-
DTC B2779 is stored.
-
Remote engine start ECU registration has not been performed.
-
Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU.
|
Body Electrical > Smart Key > Data List
Tester Display
|
Wireless C Code
|
Result
|
Proceed to
|
"No Regd" is displayed on the Techstream
|
A
|
"Regd" is displayed on the Techstream
|
B
|
A
|
|
|
3.
|
REGISTER REMOTE ENGINE STARTER ID
|
(a) Register the remote engine starter ID.
HINT:
Refer to Registration.
Click here
NEXT
|
|
|
4.
|
CHECK REMOTE ENGINE STARTER FUNCTION
|
(a) Check the remote engine starter function.
OK:
Remote engine starter functions operate normally.
OK |
|
END (REMOTE ENGINE STARTER ID WAS NOT REGISTERED)
|
5.
|
CHECK REMOTE ENGINE STARTER ECU
|
(a) Temporarily replace the remote engine starter ECU with a new one.
(b) Register the remote engine starter ID.
HINT:
Refer to Registration.
Click here
(c) Check the remote engine starter function.
OK:
Remote engine starter functions operate normally.
OK |
|
END (REMOTE ENGINE STARTER ECU WAS DEFECTIVE)
|
NG
|
|
|
6.
|
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
|
(a) Replace the main body ECU (multiplex network body ECU) with a new one.
Click here
(b) Check the remote engine starter function.
OK:
Remote engine starter functions operate normally.
OK |
|
END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)
|
|