Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001G20Y
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [11/2018 - 12/2021]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): B2782; Power Source Control ECU Malfunction; 2019 - 2021 MY RAV4 HV [11/2018 - 12/2021]

DTC

B2782

Power Source Control ECU Malfunction

DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator with ECU assembly) is determined to be abnormal.

The steering lock ECU (steering lock actuator with ECU assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator with ECU assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B2782

Power Source Control ECU Malfunction

Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the power switch is on (IG).)):

  • The steering lock motor activation command circuit has a short circuit.
  • The steering lock motor activation command circuit has an open circuit.

HINT:

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.
  • Steering lock ECU (steering lock actuator with ECU assembly)
  • Certification ECU (smart key ECU assembly)
  • Harness or connector

DTC Output Confirmation Operation:

  • Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift state park (P) and the power switch off. The steering unlocks when the power switch is turned on (ACC) or on (IG) while carrying the key.)

Vehicle Condition and Fail-safe Function when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Function when Malfunction Detected

The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started.

Prohibits the hybrid control system from being started.

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2782

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here 2019 MY RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before replacing the steering lock ECU (steering lock actuator with ECU assembly) or certification ECU (smart key ECU assembly), refer to the Registration.

    Click here 2019 MY RAV4 HV [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2020 - 2021 MY RAV4 HV [10/2019 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  • When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

PROCEDURE

1.

INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)

(a) Using an oscilloscope, check the waveform.

OK:

Tester Connection

Tool Setting

Condition

Specified Condition

G56-3 (IGE) - G56-1 (GND)

2 V/DIV., 200 ms./DIV.

Any door opened when following conditions are met, and then steering lock motor activated:

  • Shift state park (P)
  • Steering lock unlocked in advance by carrying key and turning power switch on (IG)
  • After above conditions are met, power switch turned off

Pulse generation

(See waveform)

HINT:

  • When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
  • In order to take measurements when the lock motor is operating, perform either of the following operations:
    • To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).
    • To lock the steering, turn the power switch off with the shift state park (P), and then open a door.

*a

Component with harness connected

(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))

*b

Waveform

*c

Steering Lock Motor not Operating

*d

Steering Lock Motor Operating
NG

GO TO STEP 4

OK

2.

CLEAR DTC AND DATA LIST MALFUNCTION RECORD

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

(e) Clear the DTCs.

Body Electrical > Smart Key > Clear DTCs

(f) Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.

NOTICE:

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

NEXT

3.

CHECK FOR DTC

(a) Perform the DTC output confirmation operation.

(b) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

(c) Check if DTC B2782 is output.

Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

DTC B2782 is not output.

A

DTC B2782 is output.

B
A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)
B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

4.

CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

(a) Disconnect the G56 steering lock ECU (steering lock actuator with ECU assembly) connector.

(b) Disconnect the G54 certification ECU (smart key ECU assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G56-3 (IGE) - G54-25 (SLR+)

Always

Below 1 Ω

G56-1 (GND) - Body ground

Always

Below 1 Ω

G56-3 (IGE) or G54-25 (SLR+) - Other terminals and body ground

Always

10 kΩ or higher

NOTICE:

If the result is not as specified, check for looseness in the connection which leads to ground.

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR