Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G2BY |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 - 12/2021] |
Title: LIGHTING (EXT): LIGHTING SYSTEM (w/ Headlight ECU without AFS): B243D,B243E; Left Low Beam Fan Malfunction; 2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021] |
DTC
|
B243D
|
Left Low Beam Fan Malfunction
|
DTC
|
B243E
|
Right Low Beam Fan Malfunction
|
DESCRIPTION
The headlight ECU sub-assembly operates the low beam fan to cool the headlight LED unit in order to prevent the headlight LED unit from overheating.
Illuminates the low beam headlights and continuously operates the low beam fan.
The headlight ECU sub-assembly monitors the pulse signals from the FANP terminal when the low beam fans are operating.
HINT:
If B243D or B243E is output, the headlight ECU sub-assembly performs low beam headlight dimming control.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
DTC Output from
|
Note
|
B243D
|
Left Low Beam Fan Malfunction
|
Detection condition:
-
All of the following conditions are met:
-
Ignition switch ON
-
Low beam headlights on
Malfunction status:
-
Fan speed signals from the low beam fan of less than 2900 rpm are continuously detected
|
-
Headlight LED unit assembly LH
-
Headlight unit assembly LH
-
Headlight ECU sub-assembly LH
|
HL AutoLeveling
|
for Single Beam Headlight
|
B243E
|
Right Low Beam Fan Malfunction
|
Detection condition:
-
All of the following conditions are met:
-
Ignition switch ON
-
Low beam headlights on
Malfunction status:
-
Fan speed signals from the low beam fan of less than 2900 rpm are continuously detected
|
-
Headlight LED unit assembly RH
-
Headlight unit assembly RH
-
Headlight ECU sub-assembly RH
|
HL AutoLeveling (Sub)
|
for Single Beam Headlight
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click here
PROCEDURE
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
(e) Clear the DTCs.
Body Electrical > HL AutoLeveling > Clear DTCs
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Operate the light control switch to turn on the low beam headlights and wait 30 seconds or more.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
(f) Check for DTCs.
Body Electrical > HL AutoLeveling > Trouble Codes
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
OK:
DTC B243D and B243E are not output.
Result
|
Proceed to
|
OK
|
A
|
NG (DTC B243D is output)
|
B
|
NG (DTC B243E is output)
|
C
|
B
|
|
|
3.
|
INSPECT HEADLIGHT UNIT ASSEMBLY LH
|
*a
|
Component without harness connected
(to Headlight ECU Sub-assembly LH)
|
*b
|
Component without harness connected
(to Headlight LED Unit Assembly LH)
|
(a) Remove the headlight assembly LH.
Click here
(b) Remove the headlight LED unit assembly LH.
Click here
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Wiring Color
|
Condition
|
Specified Condition
|
B-6 (FANB) - C-2
|
G
|
Always
|
Below 1 Ω
|
B-15 (FANP) - C-8
|
L
|
Always
|
Below 1 Ω
|
B-14 (FANG) - C-7
|
Y
|
Always
|
Below 1 Ω
|
OK
|
|
|
4.
|
INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
|
*a
|
Component without harness connected
(to Headlight LED Unit Assembly LH)
|
(a) Remove the headlight assembly LH.
Click here
(b) Remove the headlight LED unit assembly LH.
Click here
(c) Connect the B headlight ECU sub-assembly LH connector.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Wiring Color
|
Condition
|
Specified Condition
|
C-2 - C-7
|
G - Y
|
Low beam headlights on
|
4.75 to 5.25 V
|
C-8 - C-7
|
L - Y
|
Low beam headlights on
|
4.75 to 5.25 V
|
5.
|
INSPECT HEADLIGHT UNIT ASSEMBLY RH
|
*a
|
Component without harness connected
(to Headlight ECU Sub-assembly RH)
|
*b
|
Component without harness connected
(to Headlight LED Unit Assembly RH)
|
(a) Remove the headlight assembly RH.
Click here
(b) Remove the headlight LED unit assembly RH.
Click here
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Wiring Color
|
Condition
|
Specified Condition
|
B-6 (FANB) - C-2
|
G
|
Always
|
Below 1 Ω
|
B-15 (FANP) - C-8
|
L
|
Always
|
Below 1 Ω
|
B-14 (FANG) - C-7
|
Y
|
Always
|
Below 1 Ω
|
OK
|
|
|
6.
|
INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH
|
*a
|
Component without harness connected
(to Headlight LED Unit Assembly RH)
|
(a) Remove the headlight assembly RH.
Click here
(b) Remove the headlight LED unit assembly RH.
Click here
(c) Connect the B headlight ECU sub-assembly RH connector.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Wiring Color
|
Condition
|
Specified Condition
|
C-2 - C-7
|
G - Y
|
Low beam headlights on
|
4.75 to 5.25 V
|
C-8 - C-7
|
L - Y
|
Low beam headlights on
|
4.75 to 5.25 V
|
|