- Hybrid Battery Voltage
- Hybrid Battery Current
- VL-Voltage before Boosting
- VH-Voltage after Boosting
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001H3JV |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [02/2019 - ] |
| Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P1C8449; High Voltage Power Resource Circuit Short during Ready ON; 2019 - 2024 MY RAV4 HV [02/2019 - ] | ||
|
DTC |
P1C8449 |
High Voltage Power Resource Circuit Short during Ready ON |
DTC SUMMARY
MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU assembly monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects an open circuit malfunction.
HINT:
- This DTC is differentiated from P300449 based on detection timing (after ignition switch is turned to ON (READY)). If P300449 is also output at the same time, first perform troubleshooting for P300449.
- If there is a SMRG stuck open malfunction, only P1C8449 is output.
The cause of this malfunction may be one of the following:
Inverter voltage sensor (VH or VL) internal circuit malfunction
- Voltage sensor (VH or VL) malfunction
- Motor generator control ECU (MG ECU) malfunction
- Communication (wire harness) malfunction
High voltage system malfunction
- HV battery malfunction
- HV battery junction block assembly malfunction
- Inverter with converter assembly malfunction
- High-voltage wire harness malfunction
- High-voltage connector or connection malfunction
Low-voltage circuit (12 V) malfunction
- Hybrid vehicle control ECU assembly malfunction
- HV battery junction block assembly malfunction
- Low voltage wire harness malfunction
- Low voltage connector malfunction
DESCRIPTION
Refer to the description for DTC P0AE411.
Click here
![2019 - 2024 MY RAV4 HV [02/2019 - ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P0AE411; Hybrid/EV Battery Precharge Contactor Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
|---|---|---|---|---|---|
|
P1C8449 |
High Voltage Power Resource Circuit Short during Ready ON |
High-voltage circuit malfunctions between the HV battery and inverter with converter assembly. When the ignition switch is ON (READY), both "VL-Voltage before Boosting" and "VH-Voltage after Boosting" drop abnormally. The EV electric battery fuse is blown, the service plug grip is removed, SMRB or SMRG remains open, or the high-voltage cable has an open circuit. (1 trip detection logic) |
|
Comes on |
Master Warning: Comes on |
Related Data List
|
DTC No. |
Data List |
|---|---|
|
P1C8449 |
|
The following items can be helpful when performing repairs:
Data List
- Ready Signal
MONITOR DESCRIPTION
A malfunction is detected and the MIL is illuminated when the following condition is met:
A large fluctuation of DC/DC converter voltage is occurred due to power cable disconnection.
MONITOR STRATEGY
|
Related DTCs |
P3004 (INF P1C8449): Power Cable Malfunction |
|
Required sensors/components |
DC/DC converter, HV battery |
|
Frequency of operation |
- |
|
Duration |
TMC's intellectual property |
|
MIL operation |
1 driving cycle |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Hybrid vehicle control ECU assembly |
P3004 (INF P1C8449) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the Techstream on.
-
Turn the ignition switch to ON (READY) and wait for 3 minutes or more. [*1]
HINT:
- According to the display on the Techstream, read the Data List and monitor the values of "Hybrid Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.
-
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to the wiring diagram for the HV battery high-voltage line circuit.
Click here
CAUTION / NOTICE / HINT
CAUTION:
-
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
-
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
-
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
-
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here
HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
|
1. |
CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes
Powertrain > Motor Generator > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
P1C8449 only is output, or P0A9563 and DTCs except the ones in the table below are also output. |
A |
|
DTCs of hybrid control system in the tables below are output. |
B |
|
DTCs of motor generator control system in the tables below are output. |
C |
|
P0A9563 is also output. |
D |
|
Malfunction Content |
System |
Relevant DTC |
|
|---|---|---|---|
|
Microcomputer malfunction |
Hybrid control system |
P0A1B49 |
Drive Motor "A" Control Module Internal Electronic Failure |
|
P060647 |
Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
||
|
Motor generator control system |
P0A1B1F |
Generator Control Module Circuit Intermittent |
|
|
P0A1A47 |
Generator Control Module Watchdog / Safety MC Failure |
||
|
P0A1A49 |
Generator Control Module Internal Electronic Failure |
||
|
P1C2A1C |
Generator A/D Converter Circuit Circuit Voltage Out of Range |
||
|
P1C2A49 |
Generator A/D Converter Circuit Internal Electronic Failure |
||
|
P313383 |
Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect |
||
|
P313386 |
Communication Error from Generator to Drive Motor "A" Signal Invalid |
||
|
P313387 |
Communication Error from Generator to Drive Motor "A" Missing Message |
||
|
Power source circuit malfunction |
Motor generator control system |
P06D61C |
Generator Control Module Offset Power Circuit Voltage Out of Range |
|
Communication system malfunction |
Hybrid control system |
P312387 |
Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
|
System malfunction |
Hybrid control system |
P0C7600 |
Hybrid/EV Battery System Discharge Time Too Long |
|
P0D2D1C |
Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range |
||
|
P1C8349 |
High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction |
||
|
P0E311C |
Boosting Converter Voltage Sensor "A" Voltage Out of Range |
||
|
Motor generator control system |
P0D2D16 |
Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold |
|
|
P0D2D17 |
Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold |
||
|
P1CB69E |
Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On |
||
|
P0CA300 |
DC/DC Converter Step Up Voltage Performance |
||
HINT:
-
P1C8449 may be output as a result of the malfunction indicated by the DTCs above.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
(e) Turn the ignition switch off.
| B |
|
GO TO DTC CHART (HYBRID CONTROL SYSTEM)
|
| C |
|
| D |
|
|
|
2. |
CLEAR DTC |
Click here
|
|
3. |
CHECK DTC OUTPUT (HYBRID CONTROL) |
(a) Connect the Techstream to the DLC3.
(b) With the vehicle stopped, apply the parking brake and turn the ignition switch to ON (READY).
NOTICE:
Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.
HINT:
- If the ignition switch could not be turned to ON (READY), turn the ignition switch off and check for DTCs after turning the ignition switch to ON (READY) again.
- Because P300449 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.
- When the parking brake indicator (red) is illuminated after the electric parking brake switch assembly has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch assembly is pulled to the lock side one more time.
(c) Ensure the safety of the areas in front and at the back of the vehicle.
(d) Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.
HINT:
Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.
(e) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(f) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
P1C8449 is output, or no DTCs are output. |
A |
|
Ignition switch could not be turned to ON (READY) and DTC P300449 is output. |
B |
(g) Turn the ignition switch off.
| B |
|
GO TO DTC CHART (P300449)
|
|
|
4. |
CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR) |
Click here
| NG |
|
CONNECT SECURELY |
|
|
5. |
CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR) |
Click here
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (The connector is not connected securely.) |
B |
|
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) |
C |
| B |
|
CONNECT SECURELY |
| C |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR) |
Click here
| NG |
|
CONNECT SECURELY |
|
|
7. |
CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY) |
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the No. 1 HV battery cover panel RH.
Click here
(c) Disconnect the M32 HV battery junction block assembly connector.
(d) Disconnect the A31 hybrid vehicle control ECU assembly connector.
|
(e) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(f) Reconnect the A31 hybrid vehicle control ECU assembly connector.
(g) Reconnect the M32 HV battery junction block assembly connector.
(h) Install the No. 1 HV battery cover panel RH.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
8. |
CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND) |
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the No. 1 HV battery cover panel RH.
Click here
(c) Disconnect the M32 HV battery junction block assembly connector.
|
(d) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(e) Reconnect the M32 HV battery junction block assembly connector.
(f) Install the No. 1 HV battery cover panel RH.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY |
Click here
|
|
10. |
CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION) |
CAUTION:
Be sure to wear insulated gloves.
(a) Install the service plug grip.
(b) Turn the ignition switch to ON.
(c) Clear the DTCs.
Click here
(d) Turn the ignition switch off and wait for 2 minutes or more.
(e) Turn the ignition switch to ON (READY).
(f) Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Voltage, VL-Voltage before Boosting.
(g) According to the display on the Techstream, read the Data List and monitor the values of "Hybrid Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.
Powertrain > Hybrid Control > Data List
|
Tester Display |
|---|
|
VL-Voltage before Boosting |
|
Hybrid Battery Voltage |
|
Result |
Proceed to |
|---|---|
|
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. |
A |
|
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. |
B |
(h) Turn the ignition switch off.
| A |
|
END |
| B |
|
REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY
|
|
|