HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): Pattern Select Switch Eco Mode Circuit; 2019 - 2024 MY RAV4 HV [02/2019

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001H3KU
Model Year Start: 2019	Model: RAV4 HV	Prod Date Range: [02/2019 - ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): Pattern Select Switch Eco Mode Circuit; 2019 - 2024 MY RAV4 HV [02/2019 - ]

Pattern Select Switch Eco Mode Circuit

DESCRIPTION

When selecting ECO mode, the ECO mode switch (integration control and panel assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system and the hybrid vehicle control system.

WIRING DIAGRAM

PROCEDURE

1.	READ VALUE USING TECHSTREAM (CAN BUS CHECK)

Click here

Result	Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.	A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.	B

GO TO CAN COMMUNICATION SYSTEM

2.	CHECK DTC OUTPUT (HEALTH CHECK)

Click here

Result	Proceed to
No DTCs are output.	A
DTCs are output.	B

GO TO DTC CHART

3.	READ VALUE USING TECHSTREAM (ECO SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

Body Electrical > Air Conditioner > Data List

Tester Display
ECO Switch

(d) Read the value displayed on the Techstream.

Body Electrical > Air Conditioner > Data List

Tester Display

Measurement Item

Range

Normal Condition

ECO Switch

ECO mode switch (integration control and panel assembly) condition

ON or OFF

ECO mode switch (integration control and panel assembly) being turned and held:

ECO mode switch (integration control and panel assembly) not turned:

OFF

Result	Proceed to
The Techstream display changes according to the ECO mode switch (integration control and panel assembly) operation.	A
The Techstream display does not change according to the ECO mode switch (integration control and panel assembly) operation.	B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.	INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (ECO MODE)

Click here

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

5.	CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - BODY GROUND)

(a) Disconnect the G32 ECO mode switch (integration control and panel assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
G32-13 (GND) - Body ground	Always	Below 1 Ω

*a	Front view of wire harness connector (to ECO Mode Switch (Integration Control and Panel Assembly))

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.	CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))

(a) Disconnect the G46 air conditioning amplifier assembly connector.

(b) Disconnect the G32 ECO mode switch (integration control and panel assembly) connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
G46-11 (ECOS) - G32-7 (ECU)	Always	Below 1 Ω
G46-11 (ECOS) or G32-7 (ECU) - Body ground	Always	10 kΩ or higher

Front view of wire harness connector

(to Air Conditioning Amplifier Assembly)

Front view of wire harness connector

(to ECO Mode Switch (Integration Control and Panel Assembly))

(d) Reconnect the G32 ECO mode switch (integration control and panel assembly) connector.

(e) Reconnect the G46 air conditioning amplifier assembly connector.

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR