Last Modified: 05-08-2025 6.11:8.1.0 Doc ID: RM100000001H3VN
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [02/2019 - 08/2020]
Title: P710 (HYBRID TRANSMISSION / TRANSAXLE): COMBINATION SWITCH: INSPECTION; 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020]

INSPECTION

PROCEDURE

1. INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (COMBINATION SWITCH)

(a) Inspect the NORMAL mode switch:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

8 (B) - 13 (GND)

NORMAL mode switch being pushed and held

Below 1 Ω

NORMAL mode switch not pushed

10 kΩ or higher

If the result is not as specified, replace the integration control and panel assembly (combination switch).

*a

Component without harness connected

(Integration Control and Panel Assembly (Combination Switch))

(b) Inspect the SPORT mode switch:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 2WD):

Tester Connection

Condition

Specified Condition

9 (P) - 13 (GND)

SPORT mode switch being pushed and held

Below 1 Ω

SPORT mode switch not pushed

10 kΩ or higher

Standard Resistance (for AWD):

Tester Connection

Condition

Specified Condition

9 (P) - 13 (GND)

SPORT mode switch being turned and held

Below 1 Ω

SPORT mode switch not turned

10 kΩ or higher

If the result is not as specified, replace the integration control and panel assembly (combination switch).

*A

for 2WD

*B

for AWD

*a

Component without harness connected

(Integration Control and Panel Assembly (Combination Switch))

(c) Inspect the ECO mode switch:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 2WD):

Tester Connection

Condition

Specified Condition

7 (ECU) - 13 (GND)

ECO mode switch being pushed and held

Below 1 Ω

ECO mode switch not pushed

10 kΩ or higher

Standard Resistance (for AWD):

Tester Connection

Condition

Specified Condition

7 (ECU) - 13 (GND)

ECO mode switch being turned and held

Below 1 Ω

ECO mode switch not turned

10 kΩ or higher

If the result is not as specified, replace the integration control and panel assembly (combination switch).

*A

for 2WD

*B

for AWD

*a

Component without harness connected

(Integration Control and Panel Assembly (Combination Switch))

(d) for AWD:

Inspect the TRAIL mode switch:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

19 (B) - 13 (GND)

TRAIL mode switch being pushed and held

Below 1 Ω

TRAIL mode switch not pushed

10 kΩ or higher

If the result is not as specified, replace the integration control and panel assembly (combination switch).

*a

Component without harness connected

(Integration Control and Panel Assembly (Combination Switch))

(e) Inspect the illumination:

(1) Apply battery voltage to the combination switch and check that the switch illuminates.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 12 (ILL+)

Battery negative (-) → Terminal 1 (ILL-)

Illuminates

If the result is not as specified, replace the integration control and panel assembly (combination switch).

*a

Component without harness connected

(Integration Control and Panel Assembly (Combination Switch))