Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H3X3
Model Year Start: 2019 Model: RAV4 Prod Date Range: [02/2019 - 12/2021]
Title: LIGHTING (EXT): LIGHTING SYSTEM (w/ AFS): B242F; Open in B Power Line; 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]

DTC

B242F

Open in B Power Line

DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.

The power source voltage of the ECUB terminal is supplied when the main body ECU (multiplex network body ECU) turns the ECUB power supply relay (H-LP LH relay and H-LP RH relay) to ON.

The headlight ECU sub-assembly compares the power source voltage supply condition of the IG terminal and ECUB terminal and monitors the result.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Note

B242F

Open in B Power Line

Detection condition:

  • The power switch is on (IG)

Malfunction status:

  • No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal

Malfunction duration:

  • 10 seconds or more
  • Headlight ECU sub-assembly LH
  • Harness or connector
  • H-LP LH relay
  • Instrument panel junction block assembly
  • Main body ECU (multiplex network body ECU)

AFS

-

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Note

B242F

Open in B Power Line

Detection condition:

  • The power switch is on (IG)

Malfunction status:

  • No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal

Malfunction duration:

  • 10 seconds or more
  • Headlight ECU sub-assembly RH
  • Harness or connector
  • H-LP RH relay
  • Instrument panel junction block assembly
  • Main body ECU (multiplex network body ECU)

AFS (Sub)

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
  • If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

    Click here 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; LIGHTING (EXT): LIGHTING SYSTEM (w/ AFS): INITIALIZATION

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / AFS or AFS (Sub) / Clear DTCs.

(e) Clear the DTCs.

Body Electrical > AFS > Clear DTCs

Body Electrical > AFS (Sub) > Clear DTCs

NEXT

2.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Wait 10 seconds or more.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / AFS or AFS (Sub) / Trouble Codes.

(f) Check for DTCs.

Body Electrical > AFS > Trouble Codes

Body Electrical > AFS (Sub) > Trouble Codes

OK:

DTC B242F is not output.

Result

Proceed to

OK

A

NG (DTC output from headlight ECU sub-assembly LH)

B

NG (DTC output from headlight ECU sub-assembly RH)

C
A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 10

B

3.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY)

*a

Front view of wire harness connector

(to Headlight ECU Sub-assembly LH)

(a) Disconnect the headlight ECU sub-assembly LH connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

A11-13 (ECUB) - Body ground

Power switch on (IG)

11 to 14 V
NG

GO TO STEP 5

OK

4.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

(a) Disconnect the headlight ECU sub-assembly LH connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A11-12 (GND) - Body ground

Always

Below 1 Ω

*a

Front view of wire harness connector

(to Headlight ECU Sub-assembly LH)
OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.

INSPECT H-LP LH RELAY

(a) Remove the H-LP LH relay.

(b) Inspect the H-LP LH relay.

Click here 2019 - 2024 MY RAV4 RAV4 HV [02/2019 -        ]; LIGHTING (EXT): RELAY: ON-VEHICLE INSPECTION

NG

REPLACE H-LP LH RELAY
OK

6.

CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ECU SUB-ASSEMBLY LH)

(a) Remove the H-LP LH relay.

(b) Disconnect the A11 headlight ECU sub-assembly LH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 (H-LP LH relay) - A11-13 (ECUB)

Always

Below 1 Ω

3 (H-LP LH relay) or A11-13 (ECUB) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

7.

CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - BATTERY)

(a) Remove the H-LP LH relay.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

2 (H-LP LH relay) - Body ground

Power switch off

11 to 14 V

5 (H-LP LH relay) - Body ground

Power switch off

11 to 14 V

*a

Front view of wire harness connector

(to H-LP LH Relay)
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

8.

CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Remove the H-LP LH relay.

(b) Disconnect the 4F instrument panel junction block assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (H-LP LH relay) - 4F-31

Always

Below 1 Ω

1 (H-LP LH relay) or 4F-31 - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

9.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)

-

-

(a) Remove the instrument panel junction block assembly.

Click here 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4F-31 - A-15 (HRLY)

Always

Below 1 Ω
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

10.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY)

*a

Front view of wire harness connector

(to Headlight ECU Sub-assembly RH)

(a) Disconnect the headlight ECU sub-assembly RH connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

A12-13 (ECUB) - Body ground

Power switch on (IG)

11 to 14 V
NG

GO TO STEP 12

OK

11.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)

(a) Disconnect the headlight ECU sub-assembly RH connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A12-12 (GND) - Body ground

Always

Below 1 Ω

*a

Front view of wire harness connector

(to Headlight ECU Sub-assembly RH)
OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.

INSPECT H-LP RH RELAY

(a) Remove the H-LP RH relay.

(b) Inspect the H-LP RH relay.

Click here 2019 - 2024 MY RAV4 RAV4 HV [02/2019 -        ]; LIGHTING (EXT): RELAY: ON-VEHICLE INSPECTION

NG

REPLACE H-LP RH RELAY
OK

13.

CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ECU SUB-ASSEMBLY RH)

(a) Remove the H-LP RH relay.

(b) Disconnect the A12 headlight ECU sub-assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 (H-LP RH relay) - A12-13 (ECUB)

Always

Below 1 Ω

3 (H-LP RH relay) or A12-13 (ECUB) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

14.

CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - BATTERY)

(a) Remove the H-LP RH relay.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

2 (H-LP RH relay) - Body ground

Power switch off

11 to 14 V

5 (H-LP RH relay) - Body ground

Power switch off

11 to 14 V

*a

Front view of wire harness connector

(to H-LP RH Relay)
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

15.

CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Remove the H-LP RH relay.

(b) Disconnect the G44 main body ECU (multiplex network body ECU) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (H-LP RH relay) - G44-12 (HRY2)

Always

Below 1 Ω

1 (H-LP RH relay) or G44-12 (HRY2) - Body ground

Always

10 kΩ or higher
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR