Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H414
Model Year Start: 2019 Model: RAV4 Prod Date Range: [02/2019 - 12/2021]
Title: PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster): C13A2; Engine Switch/Power Switch Malfunction; 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]

DTC

C13A2

Engine Switch/Power Switch Malfunction

DESCRIPTION

When the ignition switch is turned to ON, power is supplied to the parking brake ECU assembly. This DTC is stored if the IG power source is not input to the parking brake ECU assembly when communication with other ECUs occurs.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

Note

C13A2

Engine Switch/Power Switch Malfunction

Both of the following conditions are met:

  1. Ignition switch ON
  2. When the hybrid vehicle control ECU assembly communicates with the main body ECU (multiplex network body ECU) via CAN communication, IG power supply is not received for approximately 15 seconds.
  • Wire harness or connector
  • IG power source circuit
  • Parking brake ECU assembly

Yes

An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  • The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.
  • When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the ignition switch is first turned to ON.

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (IG POWER SOURCE CIRCUIT - PARKING BRAKE ECU ASSEMBLY)

(a) Turn the ignition switch off.

(b) Disconnect the parking brake ECU assembly connector.

*a

Front view of wire harness connector

(to Parking Brake ECU Assembly)

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

M35-5 (IG) - Body ground

Ignition switch ON

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

2.

CHECK DTC

(a) Clear the DTCs.

Click here 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster): DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs

(b) Turn the ignition switch off.

(c) Check for DTCs.

Click here 2019 - 2021 MY RAV4 RAV4 HV [02/2019 - 12/2021]; PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster): DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes

DTC is output

REPLACE PARKING BRAKE ECU ASSEMBLY 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; PARKING BRAKE: ELECTRIC PARKING BRAKE ECU: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; PARKING BRAKE: ELECTRIC PARKING BRAKE ECU: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; PARKING BRAKE: ELECTRIC PARKING BRAKE ECU: REMOVAL

DTC is not output

USE SIMULATION METHOD TO CHECK