Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H4H9
Model Year Start: 2019 Model: RAV4 Prod Date Range: [02/2019 - 06/2020]
Title: A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): P106A62,P106C62; Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure; 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 06/2020]

DTC

P106A62

Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure

DTC

P106C62

Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure

DESCRIPTION

Those DTCs are designed to detect a deviation in the output characteristics of a pressure sensor.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P106A62

Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure

The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold absolute pressure sensor (Intake Manifold Absolute Pressure*) is higher than 8.69 kPa (1.26 psi) (2 trip detection logic).

  • Canister pressure sensor (canister pump module)
  • Manifold absolute pressure sensor

Comes on

DTC stored

SAE Code: P106A

P106C62

Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure

The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and atmospheric pressure sensor (Atmospheric Pressure*) is Higher than 7.89 kPa (1.14 psi) (2 trip detection logic).

  • Canister pressure sensor (canister pump module)
  • Atmospheric pressure sensor (ECM)

Comes on

DTC stored

SAE Code: P106C

*: Data List name

MONITOR DESCRIPTION

Those DTCs are stored when a deviation from pressure sensor characteristics is detected.

The pressure sensors* are checked approximately 50 minutes after the ignition switch is turned off. If the pressures detected by the pressure sensors* differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).

HINT:

  • *: P106A62 checks the canister pressure sensor and the manifold absolute pressure sensor. P106C62 checks the canister pressure sensor and atmospheric pressure sensor.
  • Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.

MONITOR STRATEGY

Related DTCs

P106A: Canister pressure sensor - manifold absolute pressure sensor rationality

P106C: Canister pressure sensor - barometric pressure sensor rationality

Required Sensors/Components (Main)

Canister pressure sensor

Atmospheric pressure sensor (ECM)

Manifold absolute pressure sensor

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

Within 65 seconds

MIL Operation

2 driving cycles

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

P106A

Monitor runs whenever the following DTCs are not stored

P0106, P0107, P0108 (Manifold absolute pressure)

P0401 (EGR system)

P0452, P0453 (Evaporative emission system pressure sensor)

Time elapsed at after engine stop

50 minutes

Time after ECM started by soak-timer

60 seconds or more

Auxiliary battery voltage

8 V or higher

Intake air temperature

-10°C (14°F) or higher

Engine coolant temperature

-10°C (14°F) or higher

P106C

Monitor runs whenever the following DTCs are not stored

None

Time elapsed at after engine stop

50 minutes

Time after ECM started by soak-timer

60 seconds or more

Auxiliary battery voltage

8 V or higher

Intake air temperature

-10°C (14°F) or higher

Engine coolant temperature

-10°C (14°F) or higher

EVAP system pressure sensor malfunction (P0451, P0452, P0453)

Not detected

TYPICAL MALFUNCTION THRESHOLDS

P106A

Difference between canister pressure and manifold absolute pressure

Higher than 8.69 kPa (1.26 psi)

P106C

Difference between canister pressure and atmospheric pressure

Higher than 7.89 kPa (1.14 psi)

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON.
  7. Turn the Techstream on.
  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

  9. Start the engine and idle for 10 seconds or more [A].
  10. Turn the ignition switch off.
  11. Leave the ignition switch off for 55 minutes [B].
  12. Turn the ignition switch to ON.
  13. Turn the Techstream on.
  14. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  15. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  17. Input the DTC: P106A62 or P106C62.
  18. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [A] through [C] again.
    • [A] to [C]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

  • Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DTC CHECK / CLEAR

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

HINT:

  • Refer to "Data List / Active Test" [Atmospheric Pressure, Intake Manifold Absolute Pressure and Vapor Pressure Pump].

    Click here 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DATA LIST / ACTIVE TEST 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DATA LIST / ACTIVE TEST

  • Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P106A62 AND/OR P106C62)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTC P106A62 is output

A

DTC P106C62 is output

B

DTC P106A62 and P106C62 are output

C

DTC P106A62 and/or P106C62 and other DTCs are output

D

HINT:

If any DTCs other than P106A62 and/or P106C62 are output, troubleshoot those DTCs first.

B

GO TO STEP 3

C

GO TO STEP 4

D

GO TO DTC CHART 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DIAGNOSTIC TROUBLE CODE CHART 2020 MY RAV4 RAV4 HV [10/2019 - 06/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): DIAGNOSTIC TROUBLE CODE CHART

A

2.

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

(a) Replace the manifold absolute pressure sensor.

Click here 2019 - 2024 MY RAV4 HV [11/2018 -        ]; A25A-FXS (EMISSION CONTROL): VACUUM SENSOR: REMOVAL

NEXT

GO TO STEP 5

3.

REPLACE ECM (ATMOSPHERIC PRESSURE SENSOR)

(a) Replace the ECM (atmospheric pressure sensor).

Click here 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL

NEXT

GO TO STEP 5

4.

REPLACE CANISTER PUMP MODULE

(a) Replace the canister pump module.

Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; A25A-FXS (EMISSION CONTROL): CANISTER (w/ Canister Pump Module): REMOVAL

NEXT

5.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

6.

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure, Vapor Pressure Pump and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List

Tester Display

Atmospheric Pressure

Intake Manifold Absolute Pressure

Vapor Pressure Pump

(e) Confirm that the difference between Intake Manifold Absolute Pressure and Vapor Pressure Pump is 8.69 kPa (1.26 psi) or less.

(f) Confirm that the difference between Atmospheric Pressure and Vapor Pressure Pump is 7.89 kPa (1.14 psi) or less.

NEXT

END