- Headlight ECU sub-assembly LH*1
- Headlight ECU sub-assembly RH*1
- Position control ECU assembly*2
- Main body ECU (multiplex network body ECU)
- Certification ECU (smart key ECU assembly)*3
- Air conditioning amplifier assembly
- Multiplex network door ECU*4
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001H5JG |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [02/2019 - 12/2021] |
| Title: NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): Open in One Side of Bus 5 Branch Line; 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021] | ||
|
Open in One Side of Bus 5 Branch Line |
DESCRIPTION
When the CAN bus main lines are normal (no open, short to ground, short to +B or short between lines) and there is an ECU or sensor on the "Communication Bus Check" screen that is indicated as not communicating or whose connection status on the "Communication Bus Check" screen changes intermittently, an open in one of the wires of a CAN bus branch line is suspected.
HINT:
If there is an ECU or sensor whose connection status changes intermittently while checking the "Communication Bus Check" screen, there may be an open circuit in one of the wires of a branch line of an ECU or sensor in the bus. If an open occurs in one of the wires of a CAN branch line, it may interfere with the communication of other ECUs or sensors resulting in an incorrect state being displayed.
|
Symptom |
Trouble Area |
|---|---|
|
*1: w/ Headlight ECU
*2: w/ Memory *3: w/ Smart Key System *4: w/ Power Back Door System |
|
|
There is an ECU or sensor that is indicated as not communicating on the "Communication Bus Check" screen or whose connection status on the "Communication Bus Check" screen changes intermittently. |
One side of CAN branch wire is open, or output signals are incomplete. |
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
-
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
![2019 - 2024 MY RAV4 HV [02/2019 - ]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
-
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
-
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
PROCEDURE
|
1. |
CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE |
(a) Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.
Click here
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Using the Techstream, perform "CAN Bus Check".
Click here
CAN Bus Check
(f) Observe the screen for approximately 2 minutes to check for ECUs and sensors that are displayed as not communicating.
(g) Perform the inspection as specified in the Problem Symptoms Table for the ECUs or sensors that are not communicating.
| NEXT |
|
GO TO CORRESPONDING COMMUNICATION STOP MODE
|
|
|