| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001H5WI |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [02/2019 - 10/2019] |
| Title: MAINTENANCE: A25A-FXS AUXILIARY BATTERY: REMOVAL; 2019 MY RAV4 HV [02/2019 - 10/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during auxiliary battery removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Lighting system (EXT)(w/ AFS) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Entune system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Entune system and safety connect system |
1 minute |
PROCEDURE
1. PRECAUTION
NOTICE:
-
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- When replacing the auxiliary battery, use a new auxiliary battery of the same dimensions and same capacity or more from the same class at a 20-hour rate.
2. REMOVE DECK BOARD ASSEMBLY
|
(a) Remove the deck board assembly. |
|
3. REMOVE REAR NO. 2 FLOOR BOARD
|
(a) Detach the 2 clips and 2 guides and remove the luggage trim service hole cover. |
|
4. REMOVE BATTERY HOLE COVER
(a) Detach the 12 claws and remove the battery hole cover.
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
|
(a) Loosen the nut, and disconnect the cable from the negative (-) auxiliary battery terminal. NOTICE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Click here
|
|
6. REMOVE AUXILIARY BATTERY
|
(a) Open the connector cover. |
|
|
(b) Loosen the nut and disconnect the cable from the positive (+) auxiliary battery terminal. |
|
|
(c) Disconnect the battery hose from the auxiliary battery. |
|
|
(d) Remove the bolt, nut and battery clamp sub-assembly as shown in the illustration. |
|
|
(e) Remove the battery insulator. |
|
(f) Remove the auxiliary battery.
|
(g) w/ No. 1 Battery Spacer: Remove the No. 1 battery spacer. |
|
|
|