Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001H8PS
Model Year Start: 2019 Model: RAV4 HV Prod Date Range: [02/2019 -           ]
Title: HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P322F11; Communication Error from Airbag to Generator Circuit Short to Ground; 2019 - 2024 MY RAV4 HV [02/2019 -        ]

DTC

P322F11

Communication Error from Airbag to Generator Circuit Short to Ground

DESCRIPTION

The motor generator ECU located in the inverter with converter assembly detects a problem in the collision signal line from the airbag sensor assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P322F11

Communication Error from Airbag to Generator Circuit Short to Ground

Short to ground in the communication circuit:

Communication from the airbag sensor assembly stopped and circuit Low has been detected for a certain period.

(1 trip detection logic)

  • Wire harness or connector
  • Airbag sensor assembly
  • Inverter with converter assembly

Does not come on

Master Warning:

Comes on

Related Data List

DTC No.

Data List

P322F11

Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. With ignition switch ON and wait for 2 minutes or more.
  7. Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

  • Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
    • Inspecting the high-voltage system
    • Disconnecting the low voltage connector of the inverter with converter assembly
    • Disconnecting the low voltage connector of the HV battery
  • To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
  • After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    *a

    Without waiting for 10 minutes

    Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): PRECAUTION

    HINT:

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

CHECK DTC OUTPUT (SRS AIRBAG)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.

(d) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

Airbag system DTCs are not output.

A

Airbag system DTCs are output.

B

(e) Turn the ignition switch off.

B

GO TO DTC CHART (AIRBAG SYSTEM) 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): DIAGNOSTIC TROUBLE CODE CHART 2021 - 2024 MY RAV4 RAV4 HV [08/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: DIAGNOSTIC TROUBLE CODE CHART

A

2.

CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): P033500,P033531; Crankshaft Position Sensor "A"+

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

3.

CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

(a) Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connector.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.

Result:

Proceed to

OK

NG

*a

Component with harness connected

(Airbag Sensor Assembly)

NG

CONNECT SECURELY

OK

4.

CHECK INVERTER WITH CONVERTER ASSEMBLY

(a) Disconnect the G70 airbag sensor assembly connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

G70-24 (GSW2) - Body ground

Ignition switch ON

11 to 14 V

NOTICE:

Turning the ignition switch to ON with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

(d) Turn the ignition switch off.

(e) Reconnect the G70 airbag sensor assembly connector.

NG

GO TO STEP 8

OK

5.

REPLACE AIR BAG SENSOR ASSEMBLY

Click here 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2021 MY RAV4 RAV4 HV [08/2020 - 12/2021]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

NEXT

6.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Motor Generator / Trouble Codes.

(d) Read and record the DTCs and freeze frame data.

(e) Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs

(f) Turn the ignition switch off.

NEXT

7.

CHECK DTC OUTPUT (MOTOR GENERATOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON and wait for 2 minutes or more.

(c) Enter the following menus: Powertrain / Motor Generator / Trouble Codes.

(d) Check for DTCs.

Powertrain > Motor Generator > Trouble Codes

Result

Proceed to

P322F11 is not output.

A

P322F11 is output.

B

(e) Turn the ignition switch off.

A

COMPLETED

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

8.

CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the A87 inverter with converter assembly connector.

(c) Disconnect the G70 airbag sensor assembly connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance (Open):

Tester Connection

Condition

Specified Condition

A87-18 (ABFS) - G70-24 (GSW2)

Ignition switch off

Below 1 Ω

Standard Resistance (Short):

Tester Connection

Condition

Specified Condition

A87-18 (ABFS) or G70-24 (GSW2) - Body ground and other terminals

Ignition switch off

10 kΩ or higher

*a

Front view of wire harness connector

(to Inverter with Converter Assembly)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

(e) Reconnect the G70 airbag sensor assembly connector.

(f) Reconnect the A87 inverter with converter assembly connector.

OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR