- DTCs are stored
- Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
- Shock or vibration during acceleration
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001H9B9 |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [02/2019 - 08/2020] |
| Title: A25A-FXS (ENGINE CONTROL): ENGINE COOLANT TEMPERATURE SENSOR: REMOVAL; 2019 - 2020 MY RAV4 HV [02/2019 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine coolant temperature sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model) |
|||
|
Pre-collision system |
|||
|
Lighting system (EXT)(w/ AFS) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Replacement of inverter with converter assembly |
Resolver learning |
|
|
|
Replacement of ECM |
Perform Vehicle Identification Number (VIN) registration |
DTC P063051 is output |
w/ Canister Pump Module:
w/o Canister Pump Module:
|
|
Grille shutter switch specification infomation |
Vehicle control history (RoB) [X260E] is stored |
|
|
|
Replacement of engine coolant temperature sensor |
Inspection after repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
PROCEDURE
1. DRAIN ENGINE COOLANT
Click here
![2019 - 2021 MY RAV4 HV [02/2019 - 12/2021]; MAINTENANCE: A25A-FXS COOLANT (for Engine): REPLACEMENT](/t3Portal/stylegraphics/info.gif)
2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Grille Shutter)
Click here
3. REMOVE INLET AIR CLEANER ASSEMBLY (w/ Grille Shutter)
Click here
4. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (w/ Grille Shutter)
Click here
5. REMOVE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR (w/ Grille Shutter)
|
(a) Disconnect the No. 2 engine coolant temperature sensor connector. |
|
|
(b) Remove the clip and No. 2 engine coolant temperature sensor from the water outlet. NOTICE: If the No. 2 engine coolant temperature sensor has been struck or dropped, replace it. |
|
6. REMOVE INVERTER WITH CONVERTER ASSEMBLY
-
for 2WD:
Click here
-
for AWD:
Click here
7. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
|
(a) Disconnect the engine coolant temperature sensor connector. |
|
|
(b) Remove the clip and engine coolant temperature sensor from the water outlet. NOTICE: If the engine coolant temperature sensor has been struck or dropped, replace it. |
|
|
|