w/ Tire Pressure Warning System:
- Tire pressure warning ECU and receiver
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HCEF |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [02/2019 - ] |
| Title: DOOR LOCK: DOOR CONTROL RECEIVER: REMOVAL; 2019 - 2024 MY RAV4 RAV4 HV [02/2019 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the door control receiver or door control and tire pressure monitoring system receiver assembly or electrical key and tire pressure monitoring system receiver assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
|
|
|
for Initialization:
for Registration:
|
w/o Smart Key System:
|
Register a new recognition code |
Wireless door lock control system (w/o Smart key system) |
|
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
w/ Tire Pressure Warning System:
|
|
|
for Initialization:
for Registration:
|
w/o Smart Key System:
|
Register a new recognition code |
Wireless door lock control system (w/o Smart key system) |
|
PROCEDURE
1. REMOVE REAR SEAT ASSEMBLY
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; SEAT: REAR SEAT ASSEMBLY: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
Click here
3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Click here
4. REMOVE DECK BOARD ASSEMBLY
Click here
5. REMOVE REAR NO. 2 FLOOR BOARD
Click here
6. REMOVE REAR FLOOR FINISH PLATE
Click here
7. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
Click here
8. REMOVE REAR DOOR SCUFF PLATE RH (for Gasoline Model)
HINT:
Use the same procedure described for the LH side.
Click here
9. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
- Pull back the rear seat side garnish RH so that the rear door opening trim weatherstrip RH can be removed.
-
Use the same procedure described for the LH side.
Click here
10. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure described for the LH side.
Click here
11. REMOVE TETHER ANCHOR BRACKET SET
Click here
12. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
Click here
13. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Click here
14. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
Click here
15. REMOVE DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System, w/ Smart Key System)
(a) Remove the bolt.
|
Bolt |
|
Connector |
(b) Detach the guide and remove the door control receiver.
(c) Disconnect the connector.
NOTICE:
- Do not subject the door control receiver to strong impacts or force, and do not drop it.
- Do not reuse the door control receiver that has been dropped.
16. REMOVE DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System, w/o Smart Key System)
HINT:
Use the same procedure described for the door control receiver.
17. REMOVE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (w/ Tire Pressure Warning System, w/o Smart Key System)
HINT:
Use the same procedure described for the door control receiver.
18. REMOVE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (w/ Tire Pressure Warning System, w/ Smart Key System)
HINT:
Use the same procedure described for the door control receiver.
|
|