- Poor idle, etc.
- Engine start function, etc.
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HJES |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [02/2019 - 08/2020] |
| Title: REAR SUSPENSION: REAR STABILIZER BAR: REMOVAL; 2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear stabilizer bar removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Gas leak from exhaust system is repaired |
Inspection After Repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Gas leak from exhaust system is repaired |
Inspection After Repair |
|
w/ Canister Pump Module:
w/o Canister Pump Module:
|
CAUTION:
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
PROCEDURE
1. REMOVE REAR WHEEL
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE TAIL EXHAUST PIPE ASSEMBLY
-
for HV Model:
Click here
-
for Gasoline Model:
Click here
3. REMOVE MAIN MUFFLER HEAT INSULATOR
|
(a) Remove the 4 nuts and main muffler heat insulator from the vehicle body. |
|
4. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH (for Gasoline Model)
Click here
5. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH (for Gasoline Model)
Click here
6. REMOVE NO. 1 ENGINE UNDER COVER (for Gasoline Model)
Click here
7. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (for Gasoline Model)
Click here
8. REMOVE FRONT FLOOR COVER LH (for Gasoline Model)
w/ Floor Under Cover:
Click here
9. REMOVE FRONT FLOOR COVER RH (for Gasoline Model)
w/ Floor Under Cover:
Click here
10. REMOVE NO. 2 FLOOR UNDER COVER (for Gasoline Model)
w/ Floor Under Cover:
Click here
11. REMOVE NO. 1 FLOOR UNDER COVER (for Gasoline Model)
w/ Floor Under Cover:
Click here
12. REMOVE LOWER NO. 2 CONTROL ARM COVER LH (w/ Cover)
Click here
13. REMOVE LOWER NO. 2 CONTROL ARM COVER RH (w/ Cover)
HINT:
Perform the same procedure as for the LH side.
14. REMOVE REAR STABILIZER LINK ASSEMBLY LH
|
(a) Loosen the nut (A) of the rear stabilizer link assembly LH. HINT: If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt. |
|
(b) Loosen the bolt of the rear stabilizer link assembly LH.
NOTICE:
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
(c) Using a jack and wooden block, support the rear No. 2 suspension arm assembly.
NOTICE:
- When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
- Make sure to perform this operation with the vehicle kept as low as possible.
|
*a |
Wooden Block |
|
*b |
Jack |
|
Wooden Block Placement Location |
|
(d) Remove the bolt, 2 nuts and rear stabilizer link assembly LH. |
|
15. REMOVE REAR STABILIZER LINK ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
16. REMOVE REAR STABILIZER BAR
|
(a) Remove the 4 bolts, rear stabilizer bar, rear No. 1 stabilizer bar bracket LH, rear No. 1 stabilizer bar bracket RH, rear No. 2 stabilizer bar bracket LH, rear No. 2 stabilizer bar bracket RH and 2 rear stabilizer bushings from the rear suspension member sub-assembly. |
|
17. REMOVE REAR LOWER STABILIZER BRACKET
|
(a) Remove the 2 rear lower stabilizer brackets from the rear stabilizer bushing. |
|
18. REMOVE REAR NO. 1 STABILIZER BAR BRACKET LH
|
(a) Remove the rear No. 1 stabilizer bar bracket LH from the rear stabilizer bushing. |
|
19. REMOVE REAR NO. 1 STABILIZER BAR BRACKET RH
HINT:
Perform the same procedure as for the LH side.
20. REMOVE REAR STABILIZER BUSHING
|
(a) Remove the 2 rear stabilizer bushings from the rear stabilizer bar. |
|
|
|