Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HJR1 |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [02/2019 - 10/2019] |
Title: WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR (for Rear Door): REMOVAL; 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Removal and installation of auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for HV model)*
|
Pre-collision system
|
Lighting system (EXT)(w/ AFS)
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for HV model)
|
|
Reset back door close position
|
Power back door system (for HV model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
-
Power window regulator motor assembly LH
-
Power window regulator motor assembly RH
-
Rear door window regulator sub-assembly LH
-
Rear door window regulator sub-assembly RH
-
Rear door glass sub-assembly LH
-
Rear door glass sub-assembly RH
-
Rear door glass run LH
-
Rear door glass run RH
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Catch protection function
-
Remote control function
-
Wireless transmitter-linked function
-
Key-linked function
-
Key-off operation function
-
Window open warning function
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Entune system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Entune system and safety connect system
|
1 minute
|
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Removal and installation of auxiliary battery terminal
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for Gasoline model)*
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system (for Gasoline model)
|
|
Reset back door close position
|
Power back door system (for Gasoline model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
-
Power window regulator motor assembly LH
-
Power window regulator motor assembly RH
-
Rear door window regulator sub-assembly LH
-
Rear door window regulator sub-assembly RH
-
Rear door glass sub-assembly LH
-
Rear door glass sub-assembly RH
-
Rear door glass run LH
-
Rear door glass run RH
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Catch protection function
-
Remote control function
-
Wireless transmitter-linked function
-
Key-linked function
-
Key-off operation function
-
Window open warning function
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Entune system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Entune system and safety connect system
|
1 minute
|
HINT:
-
Use the same procedure for the RH and LH sides.
-
Use the same procedure described for the LH side.
-
When performing disassembly for the rear door, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE NO. 2 REAR FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for A25A-FXS:
Click here
(b) for A25A-FKS:
Click here
CAUTION:
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
-
If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Click here
7. REMOVE DOOR ASSIST GRIP COVER LH
Click here
8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Click here
9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Click here
11. REMOVE REAR DOOR REAR BELT SEAL LH
Click here
12. REMOVE REAR DOOR SERVICE HOLE COVER LH
Click here
13. REMOVE REAR DOOR FRAME GARNISH LH
Click here
14. REMOVE REAR DOOR GLASS RUN LH
Click here
15. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
Click here
16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Click here
17. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Click here
18. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
(a) Using a T25 "TORX" socket wrench, remove the 3 "TORX" screws and power window regulator motor assembly LH from the rear door window regulator sub-assembly LH.
|
|
|