- Front door outside handle assembly LH (electrical key antenna)
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001HN9Z |
| Model Year Start: 2019 | Model: RAV4 HV | Prod Date Range: [02/2019 - 12/2021] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): OPERATION CHECK; 2019 - 2021 MY RAV4 HV [02/2019 - 12/2021] | ||
OPERATION CHECK
CHECK CUSTOMIZE PARAMETERS
NOTICE:
The operation check below is based on the non-customized initial condition of the vehicle.
Click here
![2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): CUSTOMIZE PARAMETERS](/t3Portal/stylegraphics/info.gif)
CHECK PUSH-BUTTON START FUNCTION
(a) Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift state park (P), check that the key indicator display is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed after the key indicator display is displayed in the combination meter assembly.
(b) While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the power switch is pressed with the brake pedal released: off → on (ACC) → on (IG) → off.
(c) With the shift state park (P), check that the steering lock operates when a door is opened.
(d) Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.
|
*a |
Inspection Point |
NOTICE:
Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.
HINT:
-
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Click here
- Perform this inspection for both inspection points.
(e) Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.
|
*a |
Inspection Point |
NOTICE:
Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.
HINT:
-
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (rear floor).
Click here
- Perform this inspection for both inspection points.
(f) Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.
|
*a |
Inspection Point |
NOTICE:
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.
HINT:
-
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear corners of the luggage compartment.
Click here
- Perform the inspection for both inspection points.
CHECK POWER SOURCE MODE CHANGING FUNCTION
(a) Check that the power source mode changes according to the chart below.
|
Shift Position |
Brake Pedal |
Power Source Mode when power switch Pressed |
|---|---|---|
|
Park (P) selected |
Released |
Off → on (ACC) → on (IG) → off |
|
Park (P) selected |
Depressed |
Off → hybrid control system starts |
|
Park (P) selected |
Depressed |
On (ACC) → hybrid control system starts |
|
Park (P) selected |
Depressed |
On (IG) → hybrid control system starts |
|
Park (P) selected |
Released / Depressed |
On (READY) → off |
|
Park (P) not selected |
Released |
On (ACC) → on (IG) → on (ACC) |
|
Park (P) not selected |
Depressed |
Off → on (IG) |
|
Park (P) not selected |
Depressed |
On (ACC) → on (IG) |
|
Park (P) not selected |
Released / Depressed |
On (READY) → on (ACC) |
CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION
(a) Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
(b) Check that the smart key system does not operate while in transmitter battery saving mode.
HINT:
To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.
CHECK ENTRY CANCEL FUNCTION
(a) Cancel the smart key system and check that all the functions of the smart key system no longer operate.
Click here
HINT:
While the smart key system is canceled, it is possible to lock and unlock the doors with the wireless function, and the hybrid control system can be started by holding the electrical key transmitter sub-assembly near the power switch.
CHECK KEY DIAGNOSTIC MODE
HINT:
- With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the buzzer.
- If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
(a) Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check(Key Diag Mode).
Body Electrical > Smart Key > Utility
|
Tester Display |
|---|
|
Communication Check(Key Diag Mode) |
(b) Inspect the appropriate item according to the following table.
|
Tester Display |
Inspection Item |
|---|---|
|
[CH1/CH2] Overhead + Driver Side*1 |
|
|
[CH1] Overhead + Driver Side*1 |
|
|
[CH2] Overhead + Driver Side*1 |
|
|
[CH1/CH2] Overhead + Passenger Side*2 |
|
|
[CH1] Overhead + Passenger Side*2 |
|
|
[CH2] Overhead + Passenger Side*2 |
|
|
[CH1/CH2] Overhead + Driver Side Rear*3 |
w/ Rear Door Entry:
|
|
[CH1] Overhead +Driver Side Rear*3 |
|
|
[CH2] Overhead + Driver Side Rear*3 |
|
|
[CH1/CH2] Overhead + Passenger Side Rear*4 |
w/ Rear Door Entry:
|
|
[CH1] Overhead + Passenger Side Rear*4 |
|
|
[CH2] Overhead + Passenger Side Rear*4 |
|
|
[CH1/CH2] Overhead + Front Room*5 |
|
|
[CH1] Overhead + Front Room*5 |
|
|
[CH2] Overhead + Front Room*5 |
|
|
[CH1/CH2] Overhead + Rear Room*6 |
|
|
[CH1] Overhead + Rear Room*6 |
|
|
[CH2] Overhead + Rear Room*6 |
|
|
[CH1/CH2] Overhead + Back Door*7 |
|
|
[CH1] Overhead + Back Door*7 |
|
|
[CH2] Overhead + Back Door*7 |
|
|
[CH1/CH2] Luggage + Back Door (inside)/Rear2*8 |
|
|
[CH1] Luggage + Back Door (inside)/Rear2*8 |
|
|
[CH2] Luggage + Back Door (inside)/Rear2*8 |
|
|
[CH1/CH2] Immobiliser Amp*9 |
|
|
[CH1] Immobiliser Amp*9 |
|
|
[CH2] Immobiliser Amp*9 |
- [CH1]: Channel 1 is set.
- [CH2]: Channel 2 is set.
-
[CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.
*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.
(c) Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the buzzer sounds.
HINT:
The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*6. For "Overhead + Rear Room"*6, the buzzer sounds in one long, continuous beep.
(d) *1: Front door outside handle assembly LH
HINT:
- Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.
- *2: Perform the same inspection for the front passenger door.
-
w/ Rear Door Entry:
*3, *4: Perform the same inspection for the rear door.
|
*a |
0.7 to 1 m (2.30 to 3.28 ft.) |
(e) *5: No. 1 indoor electrical key antenna assembly (front floor)
HINT:
Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.
|
*a |
Inspection Point |
(f) *6: No. 1 indoor electrical key antenna assembly (rear floor)
HINT:
Place the electrical key transmitter sub-assembly on the rear seat cushion.
|
*a |
Inspection Point |
(g) *7: Electrical key antenna (outside luggage compartment)
HINT:
Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.
|
*a |
0.7 to 1 m (2.30 to 3.28 ft.) |
(h) *8: No. 1 indoor electrical key antenna assembly (inside luggage compartment)
HINT:
Place the electrical key transmitter sub-assembly on the luggage room floor.
|
*a |
Inspection Point |
(i) *9: Amplifier (power switch)
HINT:
While facing the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the transmitter near the power switch.
|
*1 |
Power Switch |
|
*2 |
Electrical Key Transmitter Sub-assembly |
|
|