INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

(a) Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut. NOTICE: Insert the bolt with the threaded end facing the rear of the vehicle. Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

(b) Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

(c) Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 3 bolts and nut. Torque: Bolt A : 135 N·m {1377 kgf·cm, 100 ft·lbf} Bolt B : 75 N·m {765 kgf·cm, 55 ft·lbf}

2. INSTALL NO. 2 FLEXIBLE HOSE BRACKET

(a) Install the No. 2 flexible hose bracket to the rear axle carrier sub-assembly with the bolt. Torque: 29 N·m {296 kgf·cm, 21 ft·lbf}

3. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

4. INSTALL REAR LOWER COIL SPRING INSULATOR LH

Click here

5. INSTALL REAR COIL SPRING LH

Click here

6. INSTALL STABILIZE SUSPENSION

Click here

7. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

(a) Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

8. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Install the rear No. 1 suspension arm assembly with the bolt and nut. Torque: 73 N·m {744 kgf·cm, 54 ft·lbf} NOTICE: Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

9. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Click here

10. INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

Click here

11. INSTALL REAR STABILIZER LINK ASSEMBLY LH

Click here

12. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

Click here

13. INSTALL REAR DISC

Click here

14. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

(a) Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts. Torque: 107 N·m {1091 kgf·cm, 79 ft·lbf}

15. CONNECT REAR FLEXIBLE HOSE

(a) Connect the rear flexible hose to the rear flexible hose bracket with the bolt. Torque: 29 N·m {296 kgf·cm, 21 ft·lbf}

16. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Click here

17. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut. Torque: 15.5 N·m {158 kgf·cm, 11 ft·lbf}

(b) Engage the 2 clamps.

(c) Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.

(d) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.

18. INSTALL LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Click here

19. INSTALL REAR WHEEL

Click here

20. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

(a) Connect the reservoir level switch connector.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

Click here

(c) Perform the following procedure if air bleeding is not necessary:

(1) Turn the ignition switch on (READY).

(2) Depress the brake pedal and release it.

(3) Clear the DTCs.

Click here

21. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

(a) Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click here

22. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Click here

23. CHECK FOR SPEED SENSOR SIGNAL

24. PERFORM INITIALIZATION

Click here