Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001K1AD
Model Year Start: 2020 Model: RAV4 Prod Date Range: [10/2019 - 01/2020]
Title: UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): TRANSMISSION WIRE: REMOVAL; 2020 MY RAV4 [10/2019 - 01/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission wire removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)

Stop and start system

2019 - 2021 MY RAV4 [11/2018 - 12/2021]; STOP AND START: STOP AND START SYSTEM: PRECAUTION

Perform steering sensor zero point calibration

Lane control system

2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for Gasoline model)*

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system (for Gasoline model)

2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Reset back door close position

Power back door system (for Gasoline model)

2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

System Name

See Procedure

Vehicle enrolled in Toyota Audio Multimedia system or safety connect system

6 minutes

Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system

1 minute

PROCEDURE

1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

3. REMOVE NO. 1 ENGINE UNDER COVER

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. REMOVE FRONT FENDER APRON SEAL LH

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

6. DRAIN AUTOMATIC TRANSAXLE FLUID

(a) Remove the refill plug and gasket from the automatic transaxle case sub-assembly.

(b) Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.

(c) Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.

*1

No. 1 Transmission Oil Filler Tube

(d) Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:

1.7 N·m {17 kgf·cm, 15 in·lbf}

(e) Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

(f) Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

7. REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System)

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; A25A-FKS (ENGINE CONTROL): VACUUM SWITCHING VALVE (for Engine Mounting): REMOVAL

8. REMOVE FRONT ENGINE MOUNTING INSULATOR

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; A25A-FKS (ENGINE CONTROL): ACTIVE CONTROL ENGINE MOUNT (for Front Side): REMOVAL+

9. SEPARATE OIL COOLER UNION SUB-ASSEMBLY

(a) Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.

*1

Oil Cooler Union Bolt

(b) Remove the oil cooler union bolt and 2 gaskets to separate the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.

10. REMOVE TRANSMISSION CASE SIDE COVER

(a) Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.

*A

for AW (AISIN AW) Made

*B

for AWNC (AISIN AW) Made

11. REMOVE TRANSMISSION WIRE (w/o Stop And Start System)

(a) Disengage the claw, rotate the lever and disconnect the transmission wire connector.

(b) Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.

*a

Connector (A)

*b

Connector (B)

(c) Disconnect the 9 solenoid valve connectors.

HINT:

  • Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
  • Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.

(d) Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.

(e) Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.

(f) Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.

12. REMOVE TRANSMISSION WIRE (w/ Stop And Start System)

(a) Disengage the claw, rotate the lever and disconnect the transmission wire connector.

(b) Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.

*a

Connector (A)

*b

Connector (B)

(c) Disconnect the 9 solenoid valve connectors.

HINT:

  • Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
  • Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.

(d) Disengage the wire harness clamp to disconnect the transmission wire (oil pump with solenoid assembly).

(e) Disconnect the transmission wire connector.

(f) Disengage the clamp to disconnect the transmission wire (oil pump with solenoid assembly) from the solenoid lock plate.

(g) Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.

(h) Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.

(i) Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.