INSTALLATION

PROCEDURE

1. INSTALL NAVIGATION ECU

2. INSTALL NO. 2 MULTI-MEDIA MODULE BRACKET

(a) w/o Mayday System:

(1) for Type A: Install the No. 2 multi-media module bracket with the 2 screws. Torque: 3.0 N·m {31 kgf·cm, 27 in·lbf}

(2) for Type B: Install the No. 2 multi-media module bracket with the 2 screws. Torque: 3.0 N·m {31 kgf·cm, 27 in·lbf}

(b) w/ Mayday System:

(1) Install the No. 2 multi-media module bracket with the 4 screws. Torque: 3.0 N·m {31 kgf·cm, 27 in·lbf}

3. INSTALL NO. 1 MULTI-MEDIA MODULE BRACKET

(a) w/o Mayday System:

(1) for Type A: Install the No. 1 multi-media module bracket with the 2 screws. Torque: 3.0 N·m {31 kgf·cm, 27 in·lbf}

(2) for Type B: Install the No. 1 multi-media module bracket with the 2 screws. Torque: 3.0 N·m {31 kgf·cm, 27 in·lbf}

(b) w/ Mayday System:

(1) Install the No. 1 multi-media module bracket with the 3 screws. Torque: 3.0 N·m {31 kgf·cm, 27 in·lbf}

4. INSTALL TELEPHONE ECU WIRE (TO TRANSCEIVER) (w/ Mayday System)

(a) Connect the 2 connectors to install the telephone ECU wire (to transceiver).

5. INSTALL NO. 2 NAVIGATION WIRE

(a) w/o Mayday System:

(1) for Type A: Attach the clamp to install the No. 2 navigation wire. Connect the connector.

(2) for Type B: Attach the clamp to install the No. 2 navigation wire. Connect the connector.

(b) w/ Mayday System:

(1) Attach the clamp to install the No. 2 navigation wire.

(2) Connect the connector.

6. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

(a) w/o Mayday System:

(1) for Type A: Attach the clamp to install the No. 2 antenna cord sub-assembly. Connect the connector.

(2) for Type B: Attach the clamp to install the No. 2 antenna cord sub-assembly. Connect the connector.

(b) w/ Mayday System:

(1) Attach the clamp to install the No. 2 antenna cord sub-assembly.

(2) Connect the 4 connectors.

7. INSTALL NAVIGATION ECU WITH BRACKET (w/o Mayday System)

(a) for Type A:

(1) Connect each connector.

	Place Hand Here
	Install in this Direction

(2) Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, attach the guide to temporarily install the navigation ECU with bracket.

(3) Attach the clamp and connect the 3 connectors.

	Bolt
	Connector

(4) Install the 2 bolts.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

(b) for Type B:

(1) Connect the connector.

(2) Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, attach the guide to temporarily install the navigation ECU with bracket.

	Place Hand Here
	Install in this Direction

(3) Connect the 3 connectors.

	Bolt
	Connector

(4) Install the 2 bolts.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

8. INSTALL NAVIGATION ECU WITH BRACKET (w/ Mayday System)

(a) Connect the 3 connectors.

(b) Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, attach the guide to temporarily install the navigation ECU with bracket.

	Place Hand Here
	Install in this Direction

(c) Connect the 3 connectors.

	Bolt
	Connector

(d) Install the 2 bolts.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

9. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Click here

10. INSTALL AIR CONDITIONING CONTROL ASSEMBLY

Click here

11. INSTALL CONSOLE BOX ASSEMBLY

Click here