| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001L2EH |
| Model Year Start: 2020 | Model: RAV4 | Prod Date Range: [10/2019 - ] |
| Title: MAINTENANCE: UB80E AUTOMATIC TRANSAXLE FLUID: REPLACEMENT; 2020 - 2024 MY RAV4 [10/2019 - ] | ||
REPLACEMENT
PROCEDURE
1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
Click here
![2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
Click here
3. REMOVE NO. 1 ENGINE UNDER COVER
Click here
4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here
5. REMOVE FRONT FENDER APRON SEAL LH
Click here
6. REPLACE AUTOMATIC TRANSAXLE FLUID
(a) Lift the vehicle. [#1]
NOTICE:
Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).
|
(b) Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2] |
|
|
(c) Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. [#3] |
|
|
(d) Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. [#4] |
|
|
(e) Measure the amount of automatic transaxle fluid drained. [#5] HINT: Add the same amount of automatic transaxle fluid in step [#8]. |
|
(f) Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing. [#6]
Torque:
1.7 N·m {17 kgf·cm, 15 in·lbf}
|
(g) Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing. [#7] HINT: Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level. |
|
|
(h) Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8] NOTICE: Use Toyota Genuine ATF WS. Using transmission fluid other than the above type may cause abnormal noise or vibration, or damage the transmission of your vehicle. |
|
|
(i) Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9] HINT: Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level. |
|
(j) Lower the vehicle. [#10]
(k) Start the engine. [#11]
(l) Slowly move the shift lever from P to D, and then back to P. [#12]
HINT:
- Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.
- Keep the shift lever in each position for approximately 3 seconds.
(m) Allow the engine to idle for 30 seconds to warm it up. [#13]
(n) Turn the ignition switch off. [#14]
(o) Repeat steps [#1] to [#14].
(p) Repeat steps [#1] to [#10].
7. ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID
Click here
8. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the Techstream)
Click here
9. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the Techstream)
Click here
10. ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL
Click here
11. REBUILD WORK
Click here
12. INSTALL FRONT FENDER APRON SEAL LH
Click here
13. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here
14. INSTALL NO. 1 ENGINE UNDER COVER
Click here
15. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH
Click here
16. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
Click here
|
|