Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001L5AO |
Model Year Start: 2020 |
Model: RAV4 |
Prod Date Range: [10/2019 -
] |
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DCM Communication Stop Mode; 2020 - 2024 MY RAV4 [10/2019 - ] |
DCM Communication Stop Mode
|
DESCRIPTION
Detection Item
|
Symptom
|
Trouble Area
|
DCM Communication Stop Mode
|
Any of the following conditions are met:
|
-
DCM (telephone transceiver assembly) branch wire or connector
-
Power source circuit of DCM (telephone transceiver assembly)
-
DCM (telephone transceiver assembly) ground circuit
-
DCM (telephone transceiver assembly)
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
-
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
-
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
1.
|
CHECK FOR OPEN IN CAN BUS WIRE (DCM [TELEPHONE TRANSCEIVER ASSEMBLY] BRANCH WIRE)
|
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the DCM (telephone transceiver assembly) connector.
|
|
*a
|
Front view of wire harness connector
(to DCM [Telephone Transceiver Assembly])
|
|
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G131-25 (CANP) - G131-24 (CANN)
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
Result
|
Proceed to
|
OK (w/ Stop and Start System)
|
A
|
OK (w/o Stop and Start System)
|
B
|
NG
|
C
|
C |
|
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR
|
A
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G131-20 (E) - Body ground
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
|
|
*a
|
Front view of wire harness connector
(to DCM [Telephone Transceiver Assembly])
|
|
|
(b) Reconnect the cable to the negative (-) battery terminal.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
G131-1 (+B) - Body ground
|
Always
|
10.5 to 16 V
|
G131-8 (ACC) - Body ground
|
Ignition switch ACC
|
10.5 to 16 V
|
Ignition switch off
|
Below 1 V
|
G131-18 (IG2) - Body ground
|
Ignition switch ON
|
10.5 to 16 V
|
Ignition switch off
|
Below 1 V
|
Result
|
Proceed to
|
OK
|
A
|
NG (+B, ACC or IG2 terminal)
|
B
|
NG (Other terminal)
|
C
|
C |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
3.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G131-20 (E) - Body ground
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
|
|
*a
|
Front view of wire harness connector
(to DCM [Telephone Transceiver Assembly])
|
|
|
(b) Reconnect the cable to the negative (-) battery terminal.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
G131-1 (+B) - Body ground
|
Always
|
11 to 14 V
|
G131-8 (ACC) - Body ground
|
Ignition switch ACC
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
G131-18 (IG2) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|