Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001LRBO
Model Year Start: 2020 Model: RAV4 Prod Date Range: [10/2019 - 08/2020]
Title: A25A-FKS (COOLING): FLOW SHUTTING VALVE (for ATF): REMOVAL; 2020 MY RAV4 [10/2019 - 08/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during flow shutting valve (No. 1 water by-pass hose) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)

Stop and start system

2019 - 2021 MY RAV4 [11/2018 - 12/2021]; STOP AND START: STOP AND START SYSTEM: PRECAUTION

Perform steering sensor zero point calibration

Lane control system

2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for Gasoline model)*

Pre-collision System

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system (for Gasoline Model)

2019 - 2022 MY RAV4 [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Reset back door close position

Power back door system (for Gasoline model)

2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

Replacement of ECM

Perform Vehicle Identification Number (VIN) or frame number registration

DTC P063051 is output

w/ Canister Pump Module: 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): REGISTRATION

w/o Canister Pump Module: 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM (w/o Canister Pump Module): REGISTRATION

Code registration

Engine start function

w/ Smart Key System: 2020 MY RAV4 [10/2019 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

w/o Smart Key System: 2019 - 2022 MY RAV4 [11/2018 - 10/2022]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (for Gasoline Model without Smart Key System): REGISTRATION

for UB80E:

  • If transaxle compensation code read from ECM
    • Perform reset memory
    • Transfer transaxle compensation code
    • Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

for Initialization: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

for Registration: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION

for UB80E:

  • If transaxle compensation code not read from ECM
    • Perform reset memory
    • Reset transaxle compensation code
    • Perform road test to allow ECM to learn

for UB80F:

  • If transaxle compensation code read from ECM
    • Perform reset memory
    • Transfer transaxle compensation code
    • Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

for Initialization: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

for Registration: 2019 - 2024 MY RAV4 [11/2018 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION

for UB80F:

  • If transaxle compensation code not read from ECM
    • Perform reset memory
    • Reset transaxle compensation code
    • Perform road test to allow ECM to learn

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

System Name

See Procedure

Vehicle enrolled in Toyota Audio Multimedia system or safety connect system

6 minutes

Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system

1 minute

PROCEDURE

1. REMOVE BATTERY

Click here 2020 MY RAV4 [10/2019 - 08/2020]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL

2. REMOVE ECM

Click here 2019 - 2020 MY RAV4 [11/2018 - 08/2020]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL

3. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE FRONT WHEEL LH

5. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

6. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

7. REMOVE NO. 1 ENGINE UNDER COVER

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

8. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

9. REMOVE FRONT FENDER APRON SEAL LH

Click here 2020 MY RAV4 [10/2019 - 08/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

10. DRAIN ENGINE COOLANT

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; MAINTENANCE: A25A-FKS COOLANT: REPLACEMENT+

11. REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

(a) Detach the 3 clamps and remove the transmission breather clamp.

(b) Detach the 3 clamps and remove the hose clamp.

(c) Detach the 2 clamps and disconnect the flow shutting valve (No. 1 water by-pass hose) and transmission breather hose from the hose clamp.

(d) Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the water outlet.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and water outlet.

(e) Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the transmission oil cooler.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and transmission oil cooler.

(f) Disconnect the flow shutting valve connector.

(g) Remove the bolt and flow shutting valve (No. 1 water by-pass hose).