P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL; 2020 MY RAV4 HV [10/2019

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001LRDJ
Model Year Start: 2020	Model: RAV4 HV	Prod Date Range: [10/2019 - 06/2020]
Title: P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL; 2020 MY RAV4 HV [10/2019 - 06/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
*: When performing learning using the Techstream. Click here
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for HV model)*
		Pre-collision system
		Lighting system (EXT)(w/ AFS)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for HV model)
	Reset back door close position	Power back door system (for HV model)
	Back door lock initialization	Power door lock control system
ECM (w/ Canister Pump Module)	Perform Vehicle Identification Number (VIN) registration	DTC P063051 is output
ECM (w/ Canister Pump Module)	Grill shutter switch specification infomation	Vehicle control history (RoB) [X260E] is stored
ECM (w/o Canister Pump Module)	Perform Vehicle Identification Number (VIN) registration	DTC P063051 is output
Engine assembly Air fuel ratio sensor (sensor 1) Gas leaks from exhaust system	Inspection after repair	Poor idle, etc. Engine start function, etc.
Inverter with converter assembly	Resolver learning	DTCs are stored Slight vibration at a vehicle speed of 5 km/h (3 mph) or less Shock or vibration during acceleration	for 2WD: for AWD:
Hybrid vehicle transaxle assembly	Resolver learning Initialize resolver		for 2WD: for AWD:
Front bumper assembly (Including removal and installation)	Front television camera view adjustment	Panoramic view monitor system (for HV model)
Suspension, tires, etc.	Television camera assembly optical axis (Back camera position setting)	Parking assist monitor system
Suspension, tires, etc.	Parking assist ECU initialization Adjust steering angle	Panoramic view monitor system (for HV model)
Replacement of the headlight ECU sub-assembly LH	Synchronize the vehicle information Perform headlight ECU sub-assembly LH initialization	Lighting system (EXT)(w/ Headlight ECU)
Front wheel alignment adjustment	Clear zero point calibration data. Perform yaw rate and acceleration sensor zero point calibration.	DTCs are stored ABS warning light illuminates Brake warning light / yellow (minor malfunction) illuminates Slip indicator light illuminates VSC disabled or malfunctions

CAUTION:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
for 2WD:

Click here

for AWD:

Click here
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

*a	An Object Exceeding Weight Limit of Engine Lifter

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system	1 minute

If the ECM has been struck or dropped, replace it.
Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
Click here

PROCEDURE

1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.

for 2WD:
Click here
for AWD:
Click here

2. REMOVE ENGINE ASSEMBLY WITH HYBRID VEHICLE TRANSAXLE ASSEMBLY

Click here

3. REMOVE FUEL DELIVERY GUARD

Click here

4. INSTALL ENGINE HANGERS

Click here

5. REMOVE STEERING GEAR HEAT INSULATOR

Click here

6. DISCONNECT WIRE HARNESS

Click here

7. DISCONNECT ENGINE WIRE

(a) Remove the 2 bolts.

(b) Disconnect the 5 clamps.

8. DISCONNECT HV AIR CONDITIONING WIRE

(a) for 2WD:

(1) Remove the bolt.

(2) Detach the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.

*A	for 2WD
*B	for AWD

(b) for AWD:

(1) Remove the 2 bolts.

(2) Detach the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.

9. REMOVE STARTER HOLE INSULATOR

(a) Remove the 2 bolts and starter hole insulator from the engine assembly.

10. REMOVE FLYWHEEL HOUSING SIDE COVER

(a) Remove the flywheel housing side cover from the engine assembly.

11. REMOVE FRONT FRAME ASSEMBLY

Click here

12. REMOVE FRONT ENGINE MOUNTING INSULATOR

(a) Remove the bolt and front engine mounting insulator from the transverse engine engine mounting bracket.

13. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

(a) Remove the 3 bolts and transverse engine engine mounting bracket from the hybrid vehicle transaxle assembly.

14. REMOVE REAR ENGINE MOUNTING INSULATOR

Click here

15. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the bolt and wire harness clamp bracket from the rear engine mounting insulator.

16. REMOVE REAR ENGINE MOUNTING BRACKET

(a) Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.

17. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

(a) Remove the 8 bolts and hybrid vehicle transaxle assembly from the engine assembly.

NOTICE:

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.
To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.

18. REMOVE MOTOR CABLE

Click here

19. REMOVE MOTOR COOLING COOLER

Click here

20. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

(a) Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.

21. REMOVE HOSE BRACKET

(a) Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.

22. REMOVE TRANSMISSION WIRE

(a) Disconnect the connector.

(b) Remove the bolt and transmission wire from the hybrid vehicle transaxle assembly.

23. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the 4 bolts and 4 wire harness clamp brackets from the hybrid vehicle transaxle assembly.

24. REMOVE TRANSAXLE HOUSING PLUG

(a) Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.

25. REMOVE STUD BOLT

(a) Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.

26. REMOVE TRANSAXLE UNDER STOPPER BRACKET

(a) Remove the 4 bolts and transaxle under stopper bracket from the hybrid vehicle transaxle assembly.

27. REMOVE TRANSAXLE CASE PROTECTOR (for AWD)

(a) Remove the 2 bolts.

Clip

(b) Remove the clip and transaxle case protector from the hybrid vehicle transaxle assembly.