GF2A (TRANSFER / 4WD / AWD): TRANSFER ASSEMBLY: REMOVAL; 2020 MY RAV4 [10/2019

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001LREY
Model Year Start: 2020	Model: RAV4	Prod Date Range: [10/2019 - 08/2020]
Title: GF2A (TRANSFER / 4WD / AWD): TRANSFER ASSEMBLY: REMOVAL; 2020 MY RAV4 [10/2019 - 08/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the transfer assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replacement Part or Procedure	Necessary Procedure	Effect/Inoperative when not Performed	Link
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system
	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system*
		Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
	Reset back door close position	Power back door system
	Back door lock initialization	Power door lock control system
Automatic transaxle assembly	Perform reset memory Input transaxle compensation code into ECM Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: for Registration:
Automatic transaxle fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
Front electro magnetic control clutch sub-assembly	Disconnect system function check	Dynamic torque vectoring AWD system
Front wheel alignment adjustment	Perform reset memory Perform acceleration sensor zero point calibration and store system information memorization.	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.)	Television camera assembly optical axis (Back camera position setting)	Parking assist monitor system
	Parking assist ECU initialization	Panoramic view monitor system
	Perform headlight ECU sub-assembly LH initialization	Lighting system (EXT)(w/ Headlight ECU)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system	1 minute

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

*a	An Object Exceeding Weight Limit of Engine Lifter

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.

*a	An Object Exceeding Weight Limit of Transmission Jack

PROCEDURE

1. REMOVE TRANSAXLE ASSEMBLY

Click here

2. REMOVE PROPELLER SHAFT HEAT INSULATOR

Click here

3. REMOVE NO. 1 PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY

(a) Remove the 2 bolts and No. 1 propeller shaft heat insulator bracket sub-assembly.

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

4. REMOVE REAR ENGINE MOUNTING INSULATOR

Click here

5. REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

Click here

6. REMOVE TRANSFER ASSEMBLY

(a) Remove the 8 nuts and transfer assembly from the transaxle.

7. REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Click here

8. REMOVE WIRING HARNESS CLAMP BRACKET

(a) Disconnect the 3 clamps and 2 connectors.

(b) Remove the 3 bolts, 3 wiring harness clamp brackets and clutch control solenoid wire.