- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001LUB5 |
| Model Year Start: 2020 | Model: RAV4 | Prod Date Range: [10/2019 - 08/2020] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat): REMOVAL; 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat side airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) auxiliary battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
w/ Occupant Classification System: Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
w/ Occupant Classification System: Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
-
Be sure to read precaution thoroughly before servicing.
w/ Occupant Classification System:
Click here
![2019 - 2020 MY RAV4 RAV4 HV [02/2019 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (w/ Occupant Classification System): PRECAUTION](/t3Portal/stylegraphics/info.gif)
w/o Occupant Classification System:
Click here
-
Wear protective gloves. Sharp areas on the parts may injure your hands.
- There is risk of injury.
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
-
for A25A-FKS:
Click here
-
for A25A-FXS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE FRONT SEAT ASSEMBLY LH
Click here
7. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)
Click here
8. REMOVE RECLINING HINGE COVER LH
Click here
9. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Click here
10. REMOVE SEAT ADJUSTER COVER CAP LH (for Driver Side)
Click here
11. REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)
Click here
12. REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
Click here
13. REMOVE FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)
Click here
14. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
Click here
15. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH
Click here
16. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Click here
17. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH
CAUTION:
- When storing the front seat airbag assembly LH, keep the airbag deployment side facing upward.
- If the airbag deploys for any reason, it may cause a serious accident.
|
Deployment Side |
|
(a) Detach the wire harness clamp. |
|
(b) Remove the 2 nuts and front seat airbag assembly LH.
CAUTION:
- Do not reuse the nut.
- If the installation surface or surrounding area of the front seat airbag assembly LH is deformed or damaged, replace the front seatback frame sub-assembly LH with a new one.
|
|