| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001OBC0 |
| Model Year Start: 2020 | Model: RAV4 HV | Prod Date Range: [06/2020 - ] |
| Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): Shut Down Signal Circuit; 2020 - 2024 MY RAV4 HV [06/2020 - ] | ||
|
Shut Down Signal Circuit |
DESCRIPTION
The cause of the malfunction may be a shutdown signal.
Check whether there is a shutdown signal +B short circuit.
Related Parts Check
|
Area |
Inspection |
|---|---|
|
HSDN terminal |
Check that the HSDN terminal voltage decreases to check for an open or short circuit while READY off (IG ON). |
|
Hybrid vehicle control ECU assembly, inverter, wire harness |
Check for open or short circuit in hybrid vehicle control ECU assembly, inverter and wire harness. |
SYSTEM DESCRIPTION
Power supply to the motor is cut off due to a shutdown signal sent from the hybrid vehicle control ECU assembly to the motor generator control ECU (MG ECU).
WIRING DIAGRAM
Refer to the wiring diagram for the ECU power source circuit.
Click here
![2020 - 2024 MY RAV4 HV [06/2020 - ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): ECU Power Source Circuit+](/t3Portal/stylegraphics/info.gif)
CAUTION / NOTICE / HINT
This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.
If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.
CAUTION:
-
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
-
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
-
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
-
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
*a
Without waiting for 10 minutes
Click here
HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
|
1. |
CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY |
(a) Turn the ignition switch to ON.
(b) Measure the voltage according to the value(s) in the table below.
|
*a |
Component with harness connected (Hybrid Vehicle Control ECU Assembly) |
- |
- |
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A29-6 (HSDN) - A30-3 (E1) |
Ignition switch ON |
Below 4.5 V |
(c) Turn the ignition switch off.
| OK |
|
SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC) |
|
|
2. |
CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY) |
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the A87 inverter with converter assembly connector.
(c) Disconnect the A29 hybrid vehicle control ECU assembly connector.
(d) Connect the cable to the negative (-) auxiliary battery terminal.
(e) Turn the ignition switch to ON.
|
(f) Measure the voltage according to the value(s) in the table below. Standard Voltage:
NOTICE: Turning the ignition switch to ON with the hybrid vehicle control ECU assembly and inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection. |
|
(g) Turn the ignition switch off.
(h) Disconnect the cable from the negative (-) auxiliary battery terminal.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A87-6 (HSDN) - A87-36 (+B) |
Ignition switch off |
10 kΩ or higher |
|
A87-6 (HSDN) - A87-35 (+B2) |
Ignition switch off |
10 kΩ or higher |
|
A29-6 (HSDN) - A29-11 (+B1) |
Ignition switch off |
10 kΩ or higher |
|
A29-6 (HSDN) - A29-5 (MREL) |
Ignition switch off |
10 kΩ or higher |
(j) Reconnect the A29 hybrid vehicle control ECU assembly connector.
(k) Reconnect the A87 inverter with converter assembly connector.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK INVERTER WITH CONVERTER ASSEMBLY |
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the A87 inverter with converter assembly connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(d) Reconnect the A87 inverter with converter assembly connector.
| OK |
|
REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY
|
| NG |
|
REPLACE INVERTER WITH CONVERTER ASSEMBLY
|
|
|