| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001OOZ9 |
| Model Year Start: 2020 | Model: RAV4 | Prod Date Range: [06/2020 - 08/2020] |
| Title: A25A-FXS (ENGINE CONTROL): SFI SYSTEM (w/ Canister Pump Module): P059F73,P05A072; Active Grille Air Shutter "A" Actuator Stuck Closed; 2020 MY RAV4 RAV4 HV [06/2020 - 08/2020] | ||
|
DTC |
P059F73 |
Active Grille Air Shutter "A" Actuator Stuck Closed |
|
DTC |
P05A072 |
Active Grille Air Shutter "A" Actuator Stuck Open |
DESCRIPTION
The grille shutter system is composed of the radiator shutter sub-assembly and grille shutter ECU (swing grille actuator assembly).
When the certain vehicle conditions are met, the grille shutter system operates the swing grille actuator assembly to open and close the radiator shutter sub-assembly and control the volume of air flowing through the radiator assembly into the engine compartment. This results in increased thermal efficiency and increased fuel economy due to reduced aerodynamic drag. This control is performed based on signals received via CAN communication: vehicle speed signal, engine coolant temperature signal, hybrid inverter coolant temperature signal, ambient temperature signal and refrigerant pressure.
If the grille shutter ECU (swing grille actuator assembly) detects a malfunction in itself or any of the mechanical components of the grille shutter system, it will output a malfunction signal to the ECM and the ECM will store a DTC.
Control List
|
Control |
Description |
|---|---|
|
Closing Operation Control |
The grille shutter closes when certain conditions related to the vehicle speed, engine coolant temperature, inverter coolant temperature, ambient temperature and refrigerant pressure are met. |
|
Opening Operation Control |
The grille shutter opens when certain conditions related to the vehicle speed, engine coolant temperature, inverter coolant temperature, ambient temperature and refrigerant pressure are met. |
|
Ignition Switch Off-linked Opening Operation Control |
Opens the grille shutter when the ignition switch is turned off in order to prevent the grille shutter from becoming stuck closed while the vehicle is stopped. |
|
Ignition switch ON Closing/Opening Operation |
If the detection conditions of a DTC are met during a trip, the next time the ignition switch is turned to ON, a grille shutter opening and closing operation will be performed in order to judge if the malfunction still exists. |
|
Winter Control Mode |
Stops the grille shutter at a position other than the fully closed position and suspends grille shutter operation in order to prevent it from becoming stuck closed when the ambient temperature is 5°C (41°F) or lower. Winter control mode is canceled when the ambient temperature becomes 10°C (50°F) or higher. |
|
Retry Operation |
If a mechanical malfunction is detected during a grille shutter operation, the operation will be attempted again. |
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P059F73 |
Active Grille Air Shutter "A" Actuator Stuck Closed |
All of the following conditions are met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P059F |
|
P05A072 |
Active Grille Air Shutter "A" Actuator Stuck Open |
All of the following conditions are met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P05A0 |
HINT:
*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.
MONITOR DESCRIPTION
If the grille shutter ECU (swing grille actuator assembly) detects that the grille shutter has stopped during an opening or closing operation, due to foreign matter or a malfunction, it will send a malfunction signal to the ECM and the ECM will store a DTC.
|
Detection Condition |
DTC No. |
|---|---|
|
Closing Operation |
P059F73 (Active Grille Air Shutter "A" Actuator Stuck Closed) |
|
Opening Operation |
P05A072 (Active Grille Air Shutter "A" Actuator Stuck Open) |
MONITOR STRATEGY
|
Related DTCs |
P059F: Active grille air shutter stuck off P05A0: Active grille air shutter stuck on |
|
Required Sensors/Components (Main) |
Swing grille actuator assembly Radiator shutter sub-assembly |
|
Required Sensors/Components (Related) |
- |
|
Frequency of Operation |
Continuous |
|
Duration |
17 times |
|
MIL Operation |
2 driving cycles |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
P059F
|
Monitor runs whenever the following DTCs are not stored |
None |
|
Auxiliary battery voltage |
10.5 to 16 V |
|
Command to close active grille air shutter |
On |
|
Active grille air shutter motor speed sensor range check fail |
Not occurred |
|
Shutter control timeout condition*1 |
Not met |
|
Active grille air shutter Control Circuit fail |
Not occurred |
|
Lost communication with hybrid control module |
Not occurred |
|
Active grille air shutter control module fail |
Not occurred |
|
Motor lock condition*2 |
Met |
|
Active grille air shutter first operation |
Close |
|
Either of the following conditions is met |
1 or 2 |
|
1. Number of active grille air shutter motor speed sensor 1 signal pulse |
1 time or more |
|
2. Time after active grille air shutter open control is operated |
0.61 seconds or more |
P05A0
|
Monitor runs whenever the following DTCs are not stored |
None |
|
Auxiliary battery Voltage |
10.5 to 16 V |
|
Command to open active grille air shutter |
On |
|
Active grille air shutter motor speed sensor range check fail |
Not occurred |
|
Shutter control timeout condition*1 |
Not met |
|
Active grille air shutter Control Circuit fail |
Not occurred |
|
Lost communication with hybrid control module |
Not occurred |
|
Active grille air shutter control module fail |
Not occurred |
|
Motor lock condition*2 |
Met |
|
Either of the following conditions is met |
1 or 2 |
|
1. Number of active grille air shutter motor speed sensor 1 signal pulse |
1 time or more |
|
2. Time after active grille air shutter close control is operated |
0.61 seconds or more |
|
*1: Shutter control timeout condition judgment |
- |
|
Either of the following conditions is met |
1 or 2 |
|
1. Time after active grille air shutter close control is operated |
11 seconds or more |
|
2. Time after active grille air shutter open control is operated |
11 seconds or more |
|
*2: Motor lock condition judgment |
- |
|
Either of the following conditions is met |
1 or 2 |
|
1. All of the following conditions are met |
- |
|
Number of active grille air shutter motor speed sensor 1 signal pulse |
Less than 24 times |
|
Pulse period of active grille air shutter motor speed sensor 1 signal |
0.61 seconds or more |
|
Pulse period of active grille air shutter motor speed sensor 2 signal |
0.61 seconds or more |
|
2. All of the following conditions are met |
- |
|
Number of active grille air shutter motor speed sensor 1 signal pulse |
24 times or more |
|
Pulse period of active grille air shutter motor speed sensor 1 signal |
0.25 seconds or more |
|
Pulse period of active grille air shutter motor speed sensor 2 signal |
0.25 seconds or more |
TYPICAL MALFUNCTION THRESHOLDS
P059F
|
Both of the following conditions are met |
- |
|
Active grille air shutter first operation |
Close |
|
Number of active grille air shutter motor speed sensor 1 signal pulse |
1 time or more |
P05A0
|
Both of the following conditions are met |
- |
|
Active grille air shutter first operation |
Open |
|
Number of active grille air shutter motor speed sensor 1 signal pulse |
1 time or more |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
- According to the display on the Techstream, change the grille shutter control mode from normal mode to maintenance mode.
- Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
-
According to the display on the Techstream, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
OK:
"Normal" is displayed.
- Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
-
According to the display on the Techstream, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
OK:
"Normal" is displayed.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.
-
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
for 2WD with NICKEL METAL HYDRIDE BATTERY
Click here
![2019 - 2020 MY RAV4 HV [11/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY](/t3Portal/stylegraphics/info.gif)
for AWD with NICKEL METAL HYDRIDE BATTERY
Click here
for LITHIUM-ION BATTERY
Click here
(Select Powertrain in Health Check and then check the time stamp data.)
Click here
-
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
for 2WD with NICKEL METAL HYDRIDE BATTERY
Click here
for AWD with NICKEL METAL HYDRIDE BATTERY
Click here
for LITHIUM-ION BATTERY
Click here
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
PERFORM UTILITY USING TECHSTREAM (GRILLE SHUTTER CONTROL MODE SWITCHING) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
Body Electrical > Grille Shutter > Utility
|
Tester Display |
|---|
|
Grille Shutter Control Mode Switching |
(e) According to the display on the Techstream, change the grille shutter control mode from normal mode to maintenance mode.
|
|
2. |
INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE) |
(a) Check the area around the shutters and the links of the grille shutter for foreign matter and ice.
OK:
No foreign matter or ice.
| NG |
|
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM (GRILLE SHUTTER OPERATION) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
Body Electrical > Grille Shutter > Active Test
|
Active Test Display |
|---|
|
Shutter Closing Operation Lock Detection |
|
Data List Display |
|---|
|
Shutter Operation Lock Detection Result for Active Test |
(e) According to the display on the Techstream, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
OK:
"Normal" is displayed.
(f) Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
Body Electrical > Grille Shutter > Active Test
|
Active Test Display |
|---|
|
Shutter Opening Operation Lock Detection |
|
Data List Display |
|---|
|
Shutter Operation Lock Detection Result for Active Test |
(g) According to the display on the Techstream, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
OK:
"Normal" is displayed.
HINT:
When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.
| NG |
|
|
|
4. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(f) Turn the ignition switch off and wait for at least 30 seconds.
|
|
5. |
PERFORM UTILITY USING TECHSTREAM (GRILLE SHUTTER CONTROL MODE SWITCHING) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
Body Electrical > Grille Shutter > Utility
|
Tester Display |
|---|
|
Grille Shutter Control Mode Switching |
(e) According to the display on the Techstream, change the grille shutter control mode from maintenance mode to normal mode.
(f) Check for DTCs and make sure that DTC B1333 is not output.
Body Electrical > Grille Shutter > Trouble Codes
| NEXT |
|
END |
|
6. |
PERFORM ACTIVE TEST USING TECHSTREAM (SWING GRILLE ACTUATOR ASSEMBLY OPERATION) |
(a) Remove the radiator shutter sub-assembly.
Click here
(b) Remove the swing grille actuator assembly.
Click here
(c) Reconnect the swing grille actuator assembly connector.
(d) Connect the Techstream to the DLC3.
(e) Turn the ignition switch to ON.
(f) Turn the Techstream on.
(g) Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection.
Body Electrical > Grille Shutter > Active Test
|
Tester Display |
|---|
|
Shutter Closing Operation Lock Detection |
(h) According to the display on the Techstream, perform the Active Test and check the operation of the swing grille actuator assembly.
OK:
Operation is normal.
(i) Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection.
Body Electrical > Grille Shutter > Active Test
|
Tester Display |
|---|
|
Shutter Opening Operation Lock Detection |
(j) According to the display on the Techstream, perform the Active Test and check the operation of the swing grille actuator assembly.
OK:
Operation is normal.
HINT:
Perform "Grille Shutter Control Mode Switching and Grille Shutter Initialization" after replacing the swing grille actuator assembly.
Click here
| NG |
|
|
|
7. |
INSPECT RADIATOR SHUTTER SUB-ASSEMBLY (GRILLE SHUTTER OPERATION) |
(a) Remove the radiator shutter sub-assembly.
Click here
(b) Remove the swing grille actuator assembly.
Click here
(c) Manually open and close the radiator shutter sub-assembly and check that it moves smoothly.
OK:
Radiator shutter sub-assembly moves smoothly.
HINT:
Perform "Grille Shutter Control Mode Switching and Grille Shutter Initialization" after replacing the swing grille actuator assembly or radiator shutter sub-assembly.
Click here
| OK |
|
| NG |
|
|
8. |
REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER) |
(a) Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.
|
|
9. |
PERFORM ACTIVE TEST USING TECHSTREAM (GRILLE SHUTTER OPERATION) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
Body Electrical > Grille Shutter > Active Test
|
Active Test Display |
|---|
|
Shutter Closing Operation Lock Detection |
|
Data List Display |
|---|
|
Shutter Operation Lock Detection Result for Active Test |
(e) According to the display on the Techstream, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
OK:
"Normal" is displayed.
(f) Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
Body Electrical > Grille Shutter > Active Test
|
Active Test Display |
|---|
|
Shutter Opening Operation Lock Detection |
|
Data List Display |
|---|
|
Shutter Operation Lock Detection Result for Active Test |
(g) According to the display on the Techstream, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
OK:
"Normal" is displayed.
HINT:
When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.
| NG |
|
|
|
10. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(f) Turn the ignition switch off and wait for at least 30 seconds.
|
|
11. |
PERFORM UTILITY USING TECHSTREAM (GRILLE SHUTTER CONTROL MODE SWITCHING) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
Body Electrical > Grille Shutter > Utility
|
Tester Display |
|---|
|
Grille Shutter Control Mode Switching |
(e) According to the display on the Techstream, change the grille shutter control mode from maintenance mode to normal mode.
(f) Check for DTCs and make sure that DTC B1333 is not output.
Body Electrical > Grille Shutter > Trouble Codes
| NEXT |
|
END |
|
|