Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001OR2O
Model Year Start: 2020 Model: RAV4 HV Prod Date Range: [06/2020 -           ]
Title: HYBRID / BATTERY CONTROL: REAR MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0BFE62,P1C681F; Drive Motor "B" Phase U-V-W Current Sensor Signal Compare Failure; 2020 - 2024 MY RAV4 HV [06/2020 -        ]

DTC

P0BFE62

Drive Motor "B" Phase U-V-W Current Sensor Signal Compare Failure

DTC

P1C681F

Drive Motor "B" Phase U-V-W Current Sensor Circuit Intermittent

DTC SUMMARY

MALFUNCTION DESCRIPTION

These DTCs indicate that the current sensor value is abnormal. The cause of this malfunction may be one of the following:

Internal inverter malfunction

  • Current sensor malfunction
  • Inverter with converter assembly internal circuit malfunction

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P0BFE62

Drive Motor "B" Phase U-V-W Current Sensor Signal Compare Failure

Rear motor inverter current sensor characteristic malfunction:

The value of the total output of the U, V and W phase current sensors exceeds the threshold.*1

(1 trip detection logic)

  • Inverter with converter assembly
  • HV floor under wire (rear traction motor cable)
  • Rear traction motor with transaxle assembly
  • Wire harness or connector

Comes on

Master Warning:

Comes on

P1C681F

Drive Motor "B" Phase U-V-W Current Sensor Circuit Intermittent

The value of the total output of the U, V and W phase current sensors exceeds the threshold detected when DTC P0C7917, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored.

(1 trip detection logic)

  • Inverter with converter assembly
  • HV floor under wire (rear traction motor cable)
  • Rear traction motor with transaxle assembly
  • Wire harness or connector

Does not come on

Master Warning:

Does not come on

HINT:

*1: Under normal conditions, the value of the total output of the U, V and W phase current sensors is approximately 0.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: REAR MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Turn the ignition switch to ON (READY).
  7. Move the shift lever to D, and then accelerate until the vehicle speed is 20 km/h (12.5 mph) and the accelerator position is approximately 25%.
  8. Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.
  9. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

Refer to the wiring diagram for the Rear Motor High-voltage Circuit.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): Rear Motor High-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:

  • Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
    • Inspecting the high-voltage system
    • Disconnecting the low voltage connector of the inverter with converter assembly
    • Disconnecting the low voltage connector of the HV battery
  • To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
  • After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: REAR MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY): PRECAUTION

    HINT:

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

    *a

    Without waiting for 10 minutes

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

GO TO MOTOR GENERATOR CONTROL SYSTEM

(a) Go to Motor Generator Control System.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0BFE62; Drive Motor "B" Phase U-V-W Current Sensor Signal Compare Failure

HINT:

For the P0BFE62 and P1C681F inspection procedures, refer to the Motor Generator Control System section.

NEXT

END