- DTCs are stored
- Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
- Shock or vibration during acceleration
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001QEIW |
| Model Year Start: 2021 | Model: RAV4 HV | Prod Date Range: [08/2020 - 12/2021] |
| Title: P710 (HYBRID TRANSMISSION / TRANSAXLE): MOTOR CABLE: REMOVAL; 2021 MY RAV4 HV [08/2020 - 12/2021] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Lighting system (EXT)(w/ AFS) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
ECM |
Perform Vehicle Identification Number (VIN) registration |
DTC P063051 is output |
|
|
Grill shutter switch specification infomation |
Vehicle control history (RoB) [X260E] is stored |
|
|
|
Inverter with converter assembly |
Resolver learning |
|
for AWD with NICKEL METAL HYDRIDE BATTERY:
for LITHIUM-ION BATTERY:
|
CAUTION:
-
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
for AWD with Nickel Metal Hydride Battery:
Click here
![2019 - 2024 MY RAV4 HV [02/2019 - ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for Lithium-ion Battery:
Click here
-
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name
See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
1 minute
- If the ECM has been struck or dropped, replace it.
-
Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
Click here
PROCEDURE
1. REMOVE INVERTER WITH CONVERTER ASSEMBLY
Click here
2. REMOVE MOTOR CABLE
CAUTION:
Be sure to wear insulated gloves.
|
(a) Remove the 2 bolts and connector cover from the hybrid vehicle transaxle assembly. |
|
|
(b) Detach the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly. |
|
|
(c) Using an insulated tool, remove the 6 bolts and motor cable from the hybrid vehicle transaxle assembly. NOTICE:
|
|
|
|