A25A-FKS (LUBRICATION): OIL PUMP: REMOVAL; 2021 MY RAV4 [08/2020

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000001RCCV
Model Year Start: 2021	Model: RAV4	Prod Date Range: [08/2020 - 12/2021]
Title: A25A-FKS (LUBRICATION): OIL PUMP: REMOVAL; 2021 MY RAV4 [08/2020 - 12/2021]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
*: When performing learning using the Techstream. Click here
Battery terminal is disconnected/reconnected	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system
	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for Gasoline model)*
		Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for Gasoline model)
	Reset back door close position	Power back door system (for Gasoline model)
	Back door lock initialization	Power door lock control system
Replacement of ECM	Perform Vehicle Identification Number (VIN) registration	DTC P063051 is output
	Code registration	Engine start function	w/ Smart Key System: w/o Smart Key System:
	for UB80E: If transaxle compensation code read from ECM Perform reset memory Transfer transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: for Registration:
	for UB80F: If transaxle compensation code read from ECM Perform reset memory Transfer transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: for Registration:
Replacement of engine assembly Gas leak from exhaust system is repaired Replacement of throttle body with motor assembly Replacement of cam timing control motor with EDU assembly Removal and installation of a cam timing control motor with EDU assembly Replacement of camshaft timing gear assembly Removal and installation of a camshaft timing gear assembly Replacement of cylinder head sub-assembly Replacement of camshaft (for intake or exhaust camshaft) Replacement of camshaft timing exhaust gear assembly Replacement of port fuel injector assembly Replacement of direct fuel injector assembly Replacement of fuel pump assembly (for high pressure side) Replacement of engine coolant temperature sensor Replacement of spark plug Replacement of ignition coil assembly Replacement of EGR valve assembly Replacement of knock control sensor Replacement of air fuel ratio sensor (sensor 2)	Inspection after repair	Poor idle, etc. Engine start function, etc.
Replacement of automatic transaxle assembly	for UB80E: Reset memory Input transaxle compensation code into ECM Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: for Registration:
Replacement of automatic transaxle assembly	for UB80F: Reset memory Input transaxle compensation code into ECM Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: for Registration:
Automatic transaxle fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly	for UB60E: for UB60F:
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Television camera assembly optical axis (Back camera position setting)	Parking assist monitor system
	Parking assist ECU initialization Adjust steering angle	Panoramic view monitor system (for Gasoline model)
Front wheel alignment adjustment	Perform reset memory Perform acceleration sensor zero point calibration and store system information memorization.	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates
Front bumper assembly (Including removal and installation)	Front television camera view adjustment	Panoramic view monitor system (for Gasoline model)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system	1 minute

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here

PROCEDURE

1. REMOVE TIMING CHAIN COVER ASSEMBLY

Click here

2. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Click here

3. REMOVE OIL STRAINER SUB-ASSEMBLY

Click here

4. REMOVE ENGINE OIL LEVEL SENSOR

Click here

5. REMOVE OIL PUMP BRACKET

Click here

6. REMOVE ENGINE BALANCER ASSEMBLY

Click here

7. REMOVE OIL PUMP ASSEMBLY

(a) Remove the 3 bolts and oil pump assembly from the stiffening crankcase assembly.

8. REMOVE STIFFENING CRANKCASE ASSEMBLY

Click here

REMOVAL

CAUTION / NOTICE / HINT

Necessary Procedure After Parts Removed/Installed/Replaced

for UB80E:

for UB80F:

for UB80E:

for UB80F:

Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

PROCEDURE