| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002037P |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - 10/2022] |
| Title: SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL; 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Power back door initialization |
Power door lock control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system (for Gasoline model) |
|
||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Power back door initialization |
Power door lock control system |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
PROCEDURE
1. PRECAUTION (w/ Pretensioner and Force Limiter)
CAUTION:
Be sure to read precaution thoroughly before servicing.
Click here
![2021 - 2024 MY RAV4 RAV4 HV [08/2020 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here
2. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Click here
3. REMOVE DECK BOARD ASSEMBLY
Click here
4. REMOVE REAR NO. 2 FLOOR BOARD
Click here
5. REMOVE REAR NO. 3 FLOOR BOARD
Click here
6. REMOVE BATTERY HOLE COVER (for HV Model, w/ Pretensioner and Force Limiter)
Click here
7. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Pretensioner and Force Limiter)
-
for A25A-FKS:
Click here
-
for A25A-FXS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
8. REMOVE REAR FLOOR FINISH PLATE
Click here
9. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
Click here
10. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
11. REMOVE REAR SEATBACK ASSEMBLY LH
Click here
12. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)
Click here
13. REMOVE REAR SEATBACK ASSEMBLY RH
Click here
14. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
Click here
15. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
16. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
Click here
17. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
18. REMOVE REAR DOOR SCUFF PLATE LH
Click here
19. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure described for the LH side.
20. REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)
Click here
21. REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)
Click here
22. REMOVE BATTERY SERVICE COVER BOARD (for HV Model)
Click here
23. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
Click here
24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Pull back the rear door opening trim weatherstrip LH so that the deck trim side panel assembly LH can be removed.
Click here
25. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
- Use the same procedure described for the LH side.
- Pull back the rear door opening trim weatherstrip RH so that the deck trim side panel assembly RH can be removed.
26. REMOVE REAR SEAT SIDE GARNISH LH
Click here
27. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure described for the LH side.
28. REMOVE TETHER ANCHOR BRACKET SET
Click here
29. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
Click here
30. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Click here
31. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Click here
32. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
Click here
33. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
34. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
|
(a) Remove the bolt and the floor anchor of the rear seat outer belt assembly LH. |
|
(b) w/ Pretensioner and Force Limiter:
(1) Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
|
*a |
Locking Button |
|
Remove in this Direction |
|
Protective Tape |
HINT:
Tape the thin-bladed screwdriver tip before use.
(c) Remove the bolt and nut.
|
Bolt |
|
Nut |
(d) Detach the guide to remove the rear seat outer belt assembly LH.
|
(e) Remove the bolt. |
|
(f) Detach the guide to remove the rear seat outer belt anchor bracket sub-assembly LH.
35. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
|
(a) Remove the bolt and floor anchor of the rear seat outer belt assembly RH. |
|
(b) w/ Pretensioner and Force Limiter:
(1) Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
|
*a |
Locking Button |
|
|
Remove in this Direction |
|
|
Protective Tape |
HINT:
Tape the thin-bladed screwdriver tip before use.
(c) Remove the bolt and nut.
|
|
Bolt |
|
|
Nut |
(d) Detach the guide to remove the rear seat outer belt assembly RH.
|
(e) Remove the bolt. |
|
(f) Detach the guide to remove the rear seat outer belt anchor bracket sub-assembly RH.
|
|