- DTC judgment completed
- System normal
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002045V |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - ] |
| Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P05A212; Active Grille Air Shutter "A" Circuit Short to Battery; 2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ] | ||
|
DTC |
P05A212 |
Active Grille Air Shutter "A" Circuit Short to Battery |
DESCRIPTION
Refer to DTC P059A71.
Click here
![2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P059A71,P059A79; Active Grille Air Shutter "A" Actuator Stuck+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P05A212 |
Active Grille Air Shutter "A" Circuit Short to Battery |
Short to +B in swing grille actuator assembly or grille shutter motor drive circuit for 7.86 seconds or more (1 trip detection logic). |
Radiator shutter assembly |
Comes on |
DTC stored |
|
MONITOR DESCRIPTION
When the swing grille actuator assembly detects that there is a grille shutter circuit malfunction, a DTC request is sent to the ECM and the ECM stores a DTC.
MONITOR STRATEGY
|
Related DTCs |
P05A4: Active grille air shutter range check (High current) |
|
Required Sensors/Components (Main) |
Swing grille actuator assembly |
|
Required Sensors/Components (Related) |
- |
|
Frequency of Operation |
Continuous |
|
Duration |
7.86 seconds |
|
MIL Operation |
Immediate |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
None |
|
All of the following conditions are met |
- |
|
Battery voltage |
8 V or higher |
|
Time after ignition switch off to ON |
0.5 seconds or higher |
|
Receive LIN communication signal |
Less than 4.608 seconds |
TYPICAL MALFUNCTION THRESHOLDS
|
Active grille air shutter control circuit current |
1 A or more |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON [A].
- Turn the Techstream on.
- Wait 10 seconds or more [B].
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P05A212.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
-
[A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
CAUTION / NOTICE / HINT
NOTICE:
In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
PERFORM UTILITY USING TECHSTREAM (SWITCH GRILLE SHUTTER CONTROL MODE) |
(a) Turn the ignition switch off and wait for 30 seconds or more.
(b) According to the display on the Techstream, change the grille shutter control mode from normal mode to maintenance mode.
Powertrain > Engine > Utility
|
Tester Display |
|---|
|
Switch Grille Shutter Control Mode |
|
|
2. |
PERFORM UTILITY USING TECHSTREAM (GRILLE SHUTTER INITIALIZATION) |
(a) According to the display on the Techstream, perform initialization (nominal torque).
Powertrain > Engine > Utility
|
Tester Display |
|---|
|
Grille Shutter Initialization |
|
|
3. |
CLEAR DTC |
(a) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(b) Turn the ignition switch off and wait for at least 30 seconds.
|
|
4. |
CHECK DTC OUTPUT (DTC P05A212) |
(a) Turn the ignition switch to ON and wait 10 seconds or more.
(b) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC P05A212 is not output |
A |
|
DTC P05A212 is output |
B |
HINT:
Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.
Click here
| B |
|
|
|
5. |
READ VALUE USING TECHSTREAM (GRILLE SHUTTER CONTROL MODE) |
(a) According to the display on the Techstream, change the grille shutter control mode from maintenance mode to normal mode.
Powertrain > Engine > Utility
|
Tester Display |
|---|
|
Switch Grille Shutter Control Mode |
(b) Read the value displayed on the Techstream.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Grille Shutter Control Mode |
Standard:
|
Techstream Display |
Specified Condition |
|---|---|
|
Grille Shutter Control Mode |
Normal |
| NEXT |
|
END |
|
|